Flow Reaction Forces upon Blowdown of Safety Valves

The activation of safety valves causes the development of flow reaction forces that have to be transferred in an adequate way via the piping to the steel structure or via the connected vessel into the foundation. If the safety valve outlet piping is connected to a blowdown system or, in case of blowing off into the atmosphere, are equipped with a T‐piece at the outlet, the stationary reaction forces are compensated completely. The transient opening process, however, develops flow reaction forces which culminate in peaks of short duration. In this article, a simple method will be proposed for the estimation of the resulting reaction forces as a function of the length of the pipe at the safety valve outlet. CFD calculations and blowdown tests executed with a full‐lift safety valve have confirmed this method on principle. Special importance is attributed to the short duration of the effect of the reaction forces which seems to have only a negligible impact on the supporting steel structure.     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Kinetics of two-step anionic polymerization

This article deals with the kinetics of two-step anionic polymerization by way of a non-steady state method. Several molecular parameters can be evaluated using the formulae developed. A bimodal molecular weight distribution function for the resulting polymer is derived from the set of kinetic differential equations, which is in agreement with the experimental data reported.     

高氧化态（Ⅱ─Ⅳ）三核金属簇合物构型的人工神经网络判别方法

本文运用一典型的人工神经网络模型─“反向传播”模型，对高氧化态（Ⅱ─Ⅳ）三核金属簇合物的构型分布进行了分析，得到了较好的分类、预报结果为化合物结构分析提供了新的工具。     

Intramolecular crosslinking of poly(vinyl alcohol)

Poly(vinyl alcohol) is crosslinked in dilute solution (c=0.1 wt%) with glutaraldehyde. The reaction product is characterized by viscometry and gel permeation chromatography (g.p.c.). The intrinsic viscosity decreases with increasing degree of crosslinking and does not depend on temperature. G.p.c. reveals that the reaction product is not homogeneous, but consists of a mixture of particles with different sizes, possibly both intra- and intermolecularly crosslinked molecules. The intramolecularly crosslinked molecules are smaller in size than the initial polymer molecules and their size depends on the degree of crosslinking. They possess a narrow particle size distribution even if the initial polymer sample had a broad molecular weight distribution.     

Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

天津独流减河工程监控系统现地通信单元设计

提出一种配电网电容电流测量的新方法，在零序电压互感器的开口三角侧串联一个可调电感，通过注入一个变频恒流信号寻找配电网的谐振频率，改变可调电感的数值后寻找另一谐振频率，联立2个谐振方程求解电容电流，该方法消除了电压互感器漏抗对测量的影响。开发了配电网电容电流测量仪，经模拟试验和现场测试表明，该方法具有安全、快捷、准确等特点，适用于中性点不接地或经随调式消弧线圈接地配电网。     

Effect of electric field on the hydrodynamics of fluidized nanoparticles

The effect of electric field on the hydrodynamics of nanoparticles was studied in a fluidized rectangular bed, with electrodes attached to two parallel walls. It was shown that the electric field of the order of 3 times the gravity markedly decreased the bed expansion and increased the solids volume fraction of nanoparticles fluidized by air. In these experiments, a light diode assembly was utilized to infer the local solids volume fractions within a rectangular bed of 10 nm silica particles. These experimental measurements yielded a two dimensional solids volume fraction distribution within the rectangular bed. The experimental results provided some new insights into the distribution of solids within the bed. The agglomerate diameters were computed using a momentum balance with the drag given by the Ergun equation and the empirical Richardson-Zaki method. Both methods yielded agglomerate diameters of the order of 100 μm and showed dependence on the strength of the electric field. The electric field decreased the granular temperature of the nanoparticles.     

Low temperature synthesis of aluminium titanate by an aqueous sol-gel route

Formation of aluminium titanate (AT) has been achieved at low temperature through sol-gel process using boehmite and titanium hydroxide as precursors by controlling the particle size at nanoscale followed by in-situ peptisation. The formations of AT phase, particle size distributions, sintering and thermal expansion characteristics, and microstructural features have been reported. DTA and XRD analysis have been performed to confirm the formation of AT. A 94% relative density was obtained for aluminium titanate sintered at 1550 °C with controlled grain size in the range of 2-3 μm.     

阳平关砂金矿精选厂尾矿综合回收的研究

本文详细的介绍了陕西省阳平关砂金矿精选厂尾矿金和其他可利用的矿物综合回收方法和最佳分选流程。