脉冲电镀最佳参数之探索和优化

本文利用正交实验法对脉冲电镀各控制参数进行试验,对影响分散能力、镀层可靠性及外观质量的各种因素进行探讨,寻找影响外观质量的显著因子并加以控制,同时进一步优化脉冲电镀的工艺参数。     

Drying of Uncoated Paper with Gas-Fired Infrared Emitters—Optimum Emitters' Location Within a Paper Machine Drying Section

This article theoretically investigates the drying of uncoated paper with gas-fired infrared (IR) emitters installed within the drying section of a given commercial paper machine. Specifically, it presents the ideal location of two opposing IR emitters within the drying section. The ideal location of the two opposing IR emitters corresponds to the highest machine speed with specified average moisture content of paper sheet at the end of the drying section. This article also presents the average evaporation rate, temperature, and moisture content of the paper sheet as it travels through the drying section with the two opposing IR emitters operating at the optimum location. In addition, the temperature and moisture profiles in the sheet thickness direction, before and after the IR emitters, are provided. This article is not concerned with the potential effects of drying with IR emitters on paper sheet properties and machine runnability issues.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

箱包风格设计及其发展趋势(Ⅰ)

本文主要讨论现代箱包设计的风格定位及其流行趋势。     

Robustness of VS-MRAC with respect to unmodelled dynamics and external disturbances

A variable structure model reference adaptive controller (VS-MRAC) using only input and output measurements was recently proposed and shown to be globally asymptotically stable with superior transient behaviour and disturbance rejection properties. In this paper a singular perturbation approach is used in order to establish the robustness of the controller in the presence of unmodelled dynamics (parasitics) and disturbances. We develop a new Lyapunov-based technique to analyse the overall system and show that for sufficiently small parasitics the system remains stable and the output error is small in some sense.     

多孔挡板流化床还原UO3反应器模型的研究

针对ＵＯ＿３的Ｎ＿２还原反应建立了多孔挡板流化床反应器模型。将多孔挡板床的每一级视为具有相似的流动状态，每一级的上、下段称为稀、密相段，分别用鼓泡床和活塞流模型描述。该模型的计算值与￠６３ｍｍ的多孔挡板床Ｈ＿２还原ＵＯ＿３的热态实验值能较好的吻合。还预计了还原温度、操作气速和挡板结构参数对固相转化率的影响，为该类反应器的工业设计、放大和优化提供了依据。     

Implementing Information Systems: Some Practical Advice and a Richer Model

Recent research suggests that implementing information systems presents considerable difficulties and that many implementations are total or partial failures. This paper argues that what both practitioners and students require are richer and more acceptable models of information systems implementation. Accordingly, case study data concerning the introduction of manufacturing resource planning (MRP II) are used to illustrate five patterns of behaviour (rites) which capture important social actions; and four components of changing psychological orientation. It is argued that appreciation of the rites and psychological developments identified here will support effective change programmes. Guidelines based on our model are provided for practitioners.     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

Photoresponsive peptide and polypeptide systems: part II. Photochromism of poly(l-ornithine) containing various azo-contents in side chains

Poly(L-ornithine)s having various azo-contents in the side chains were synthesized by the water-soluble carbodiimide procedure. The photochemical properties of the polypeptides poly[N^δ-p-(phenylazo)benzoyl-L-ornithine] (PPABLO) containing 3–77 mol% azobenzene were investigated by absorption and circular dichroism spectroscopy in hexafluoro-2-propanol (HFIP) or water, and in HFIP-water or methanol-water solvent mixtures. The photochromism of the dichroic bands of the PPABLOs containing 20–77 mol% azobenzene in the visible and ultraviolet wavelength regions was found to be mostly reversible as a function of irradiation time at different wavelengths due to the photostationary state (above 80% trans-cis photoisomerization) of the azo aromatic moieties. The PPABLO containing 3.2 mol% azobenzene in water exhibited conformational changes from random coil to helix by the addition of methanol or sodium dodecyl sulphate (SDS). The photo-induced conformational change was observed in HFIP-water-SDS solvent mixtures, while no conformational change was seen in water and HFIP-water solvent mixtures.     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.