工程结构优化设计发展综述

 着重评述了工程结构优化设计研究领域从最初的尺寸优化发展到形状优化、拓扑优化的基本历程及其相关特点，并对优化设计选用的优化算法进行了归类，提出了这一领域今后仍然有待于发展的主要方面．     

矿用圆环链弯曲点的角度分布

矿用圆环链弯曲点是应力集中点 ,肩部断裂发生于该点附近 .以 2 6× 92矿用圆环链为研究对象 ,应用方向数据统计导出该点的角度分布 ,并给出了批量检验矿用圆环链尺寸匹配状况的一种方法     

Evaluation of Morphology—Stable Critical Size of KNbO3 Crystals

Skeletal form of KnbO3 crystals growing in Li2B4O7 solvent was in-situ observed at 900℃ and it was found that shallow depression started to develop on the surface of KnbO3 crystals when the crystal size exceeded several micron,typically 7 micron.Based on the quantitative criterion derived by Chernov,the estimated critical size of KNbO3 crystals was 1 micron,which was consistent with the experimental measurement.The kinetic coefficients,Kcorner and Kcr,in the criterion were experimentally obtained in the diffusive-convective and diffusive-advective flow states respectively.     

高炉鼓风机就地扩容改造方案及经济效益

介绍了利用高炉鼓风机基础实施不易地扩容改造的设计工艺方法，该方法不仅降低了设计、施工、安装费用，而且缩短了施工周期，降低了固定资产投资。     

干压陶瓷砖尺寸偏差原因分析及其解决办法

结合干压陶瓷砖尺寸的国家标准,对在实际检测过程中遇到的尺寸偏差的两种类型,举例说明,指出产生尺寸偏差的原因,进而提出解决尺寸偏差的办法。     

Influence of melt superheat on breakup process of close-coupled gas atomization

In close-coupled gas atomization（CCGA）, the influences of melt superheat on breakup process are fundamental to obtain desired or finer powder. Based on a series of Cu atomization experiment under different superheating conditions, the influences of melt superheat on breakup process were studied. Experimental results indicate that as the melt superheat is increased to 150, 200, 250 and 300 K, the mean particle size （D50） decreases consequently to 34.9, 32.3, 30.9 and 19.7 μm. Theoretical analysis reveals that the primary breakup and secondary breakup processes are close coupled, and the melt superheat radically influences the melt properties, and plays a crucial role on governing the filming process of primary breakup and the atomization modes of secondary breakup. There exists a strong nonlinear decrease of contact angle of melt to nozzle orifice wall when the superheat is increased fi＇om 250 K to 300 K, leading to a marked fall of the film thickness formed in primary breakup, and D50 of copper powders is therefore sharply reduced. However, the log-normal distribution feature of particle size has not been substantially improved.     

樟村坪磷矿房柱采矿法采场结构尺寸研究

通过分析采场结构尺寸对其稳定性的影响，得到了樟村坪磷矿房柱采矿法的矿房跨度、矿柱形状及实际支撑的矿柱尺寸。     

基于ObjectARX的国标尺寸公差快速标注技术

针对AutoCAD标注国标尺寸公差效率低的问题 ,讨论了基于ObjectARX开发平台实现快速标注的原理和方法。该技术有利于提高工作效率。     

回转体拉深件毛坯直径的简捷计算及误差分析

通用的回转体拉深件毛坯直径的计算公式繁琐，不蝗记忆，特别是利用中线尺寸常出现小数点使计算复杂，本文针对此问题分别推导出了利用中线尺寸和不用中线尺寸时，毛坯直径的简捷计算公式。并进行了误差分析，最后用实例对简捷计算方法的正确性给予了验证。