Softening and melting mechanisms of polyamides interfering with sliding stability under adhesive conditions

The thermal stability of polymers is a main issue when used as friction elements under dry sliding. Cast polyamide grades processed with either natrium or magnesium catalysors are slid on a small-scale and a large-scale test configuration to reveal the effect of softening or degradation on the sliding stability and to investigate possibilities for extrapolation of friction and wear rates between both testing scales. The combination of softening and afterwards transition into the glassy state is detrimental for the sliding stability of natrium catalysed polyamides, characterised by heavy noise during sliding. A transfer film formed under continuous softening also provides high friction. Melting during initial sliding is necessary for stabilisation in both friction and wear, and eventual softening of a molten film near the end of the test then not deteriorates the sliding stability. Softening of magnesium catalysed polyamides is favourable for the formation of a coherent transfer film resulting in more stable sliding than natrium catalysed polyamides. The differences in softening mechanisms of both polyamide grades is correlated to structural changes investigated by thermal analysis and Raman spectroscopy: the γ crystalline structure prevails in magnesium catalysed samples and the α crystalline structure is predominant in natrium catalysed samples. For internal oil lubricated polyamides, a time dependent degradation of the polyamide bulk deteriorates the supply of internal oil lubricant to the sliding interface, resulting in high friction and wear under overload conditions. As the degradation mechanisms during sliding are strongly correlated to the test set-up, extrapolation is only possible for friction in a limited application range, while wear rates cannot be extrapolated.     

Exploring single electrode reactions in polymer electrolyte fuel cells

Utilising a pseudo-reference electrode in polymer electrolyte fuel cells allows for the separation of anodic and cathodic contributions to the entire cell impedance. Modelling the impedance responses by using equivalent circuits inhibits the investigation of kinetic parameters of the basic electrochemical reactions, which take place at single electrode-electrolyte interfaces. Therefore, we evaluate single electrode impedance measurements by a kinetic model, which is based on specific reaction pathways, either for the oxygen reduction reaction (ORR) or the hydrogen oxidation reaction (HOR). As a consequence, it is possible to obtain kinetic parameters for the specific reaction of interest. Furthermore, the information gained from the single electrode impedance measurements and the kinetic model can give insight into single reactions steps. In particular, the ORR has to include a chemical step in the reaction pathway.     

Raman spectroscopic study of conformational changes in the amorphous phase of poly(lactic acid) during deformation

The conformational distribution change of amorphous poly(lactic acid) (PLA) induced by deformation has been studied using Raman spectroscopy. Spectroscopic features associated with the rotational isomeric states (ttt, ttg′, tg′t, tg′g′) have been established experimentally and supported by normal coordinate analysis. Deformation induced a significant increase in the most favorable tg′t conformation. Based on the relative intensities of Raman-active skeletal modes, a quantitative method has been developed that can be used to elucidate structural changes in a variety of deformed polymer samples. For biaxially oriented PLA films, the overall tg′t conformation increased from the 76% in undeformed sample to a value as high as 92%. The change in conformational distribution in the amorphous phase follows a different trend (76-88%) as compared to the increase in sample crystallinity (0-43%). A large change in amorphous chain conformation occurred at relatively low draw ratios. In contrast, the large change in the degree of crystallinity occurred at higher draw ratios.     

Polyaniline for corrosion prevention of mild steel coupled with copper

Polyaniline emeraldine base/epoxy resin (EB/ER) coating was investigated for corrosion protection of mild steel coupled with copper in 3.5% NaCl solution. EB/ER coating with 5-10 wt% EB had long-term corrosion resistance on both uncoupled steel and copper due to the passivation effect of EB on the metal surfaces. During the 150 immersion days, the impedance at 0.1 Hz for the coating increased in the first 1-40 days and subsequently remained constant above 10⁹ Ω cm², whereas that for pure ER coating fell below 10⁶ Ω cm² after only 30 or 40 days. Immersion tests on coated steel-copper galvanic couple showed that EB/ER coating offered 100 times more protection than ER coating against steel dissolution and coating delamination on copper, which was mainly attributed to the passive metal oxide films formed by EB blocking both the anodic and cathodic reactions. Salt spray tests showed that 100 μm EB/ER coating protected steel-copper couple for at least 2000 h.     

Polyaniline as corrosion inhibitor for iron in acid solutions

In recent years, polymer amines have been studied as an efficient corrosion inhibitor for iron in acid media. In this article, the performance of water soluble polyaniline as corrosion inhibitor for iron in 0.5M H₂SO₄ has been evaluated by potentiodynamic polarization, linear polarization, and electrochemical impedance spectroscopy and compared with the performance of the aniline monomer. It has been found that polyaniline is an efficient inhibitor, since the maximum efficiency of 84% has been observed at a concentration of 100 ppm, whereas the monomer has accelerated the corrosion. FTIR studies have shown that the polyaniline is strongly adsorbed on the iron surface and inhibits the corrosion effectively. However, aniline has been found to improve the passivation tendency of iron at higher concentrations. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2144–2153, 2006     

Proton diffusion in γ-manganese dioxide

Deconvolution of the electrolytic manganese dioxide (EMD) discharge curve has indicated the presence of a number of energetically different reduction processes. This has been used to determine the contribution of each reduction process to the total discharge. Using step potential electrochemical spectroscopy (SPECS), the i-t data were modelled as the sum of the discharge of the individual reduction processes. From this, A√ D for each reduction process as a function of degree of discharge was determined. The maximum A√ D values for each process ranged from 2.3×10⁻² to 4.0×10⁻⁴ cm³ s^−1/2 g⁻¹ values are consistent with previously reported values for A√ D, although in this case we have determined values for the entire compositional range.     

Fabrication and optical characterization of poly(2,5‐di‐n‐butoxyphenylene) nanofibril arrays

Anodic aluminum oxide (AAO) membrane can be used as template for the synthesized nanostructures. In this article, we have prepared the AAO membrane by using electrooxidation of aluminum substrate in phosphoric acid, and fabricated poly(2,5‐di‐n‐butoxyphenylene) (BuO–PPP) nanofibril arrays by oxidative coupling polymerization of 1,4‐di‐n‐butoxybenzene (DBB) within the pores of the AAO template membrane. The detailed molecular structure of the polymer nanofibrils was characterized by using infrared and ¹H nuclear magnetic resonance spectra, and estimated to consist of almost equal fractions of 1,4‐ and 1,3‐ linkages. We have used transmission electron microscopy, scanning electron microscopy, and atom force microscopy to confirm the morphologies and images of the AAO template membrane and the fabricated nanometer scale of BuO–PPP nanofibril arrays. The experimental results demonstrated that the pores of the AAO membrane were regular and uniform, and parallel each other, and the BuO–PPP chains in the narrowest template‐synthesized nanofibrils were oriented parallel to the porous axes of the AAO membrane and perpendicular to the surface of the aluminum substrate. The polymer chain orientation was partially responsible for the enhanced conductivity. The ultraviolet absorption spectrum of the BuO–PPP nanofibril arrays shown that the polymer contains a better extended π‐conjugation system along poly‐(p‐phenylene) backbone, which resulted in longer wavelength shift of the absorption band, the absorption maxima were located at 258 nm (E₁ absorption band) and 332 nm (E₂ absorption band), respectively. Photoluminescence spectrum of the BuO–PPP nanofibril arrays exhibited a blue emission. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 425–430, 2004     

碱体系中系列羟基苯基卟啉红外光谱和拉曼光谱性质研究

本文继续深入研究该体系中相关物质的红外光谱和拉曼光谱的性质.论文结果说明,在碱体系中,NaOH只与羟基苯基卟啉周边meso-位的羟基反应形成盐,这个性质与紫外可见光谱性质是一致的.同时这一结果也为研究卟啉与金属的相互作用提供了有益的理论支持.     

Characterization of self-assembled monolayers of iron and cobalt octaalkylthiosubstituted phthalocyanines and their use in nitrite electrocatalytic oxidation

Cobalt and iron phenylthiosubstituted phthalocyanines have been deposited on Au electrode surfaces through the self-assembled monolayer (SAM) technique. The so formed layers were studied using voltammetric and impedance techniques. These SAMs blocked a number of Faradic processes and electrocatalyzed the oxidation of nitrite. The electrocatalytic parameters of the cobalt and iron phenylthiosubstituted phthalocyanines deposited on Au electrodes in nitrite solution were studied. Nitrite overpotentials which are lower than ever reported were obtained in this work for the iron phenylthiosubstituted phthalocyanines with very high stability.     

Impedance spectroscopy study of hardened Portland cement paste

In this paper, the differential impedance analysis (DIA) has been applied to the study of the dielectric properties of hardened Portland cement paste. Two time constants are found in the impedance spectra obtained in the frequency region form 100 kHz to 15 MHz. One time constant has been attributed to the solid matrix and the other one to the liquid phase filling the pores. The effect of the cement paste-electrodes interface has been quantified using two different experimental set-ups. Measurements using direct contact between electrodes and cement paste have been compared with measurements using an air gap technique in which the specimen “floats” between the electrodes. The two referred time constants have been found in both types of measurements. The influence of drying on the dielectric parameters is also studied.