关于天然气水合物钻采工艺技术进展的研究

目前全球正面临着前所未有的能源危机，天然气水合物由于储量大、能量密度高而将成为一种诱人的新型能源。天然气水合物主要存在于冻土带和海洋，在地下处于低温和高压状态，以现有的技术，钻井和开采都存在很大的困难。简要介绍了天然气水合物的性质及储量，阐述了天然气水合物钻井的六个挑战及目前国外天然气水合物的两种钻探方法；同时阐述了以热力法、降压法和化学试剂注入法为主的天然气水合物开采方法，并针对天然气水合物钻采技术现状指出了下一步的研究方向。     

加油站油品防盗的措施

为防止加油站油品被盗，应采取加强夜间值班管理、加强油品的计量管理和加强安全管理的高科技建设三项措施。     

北部湾盆地福山凹陷CO2气成因探讨

北部湾盆地福山凹陷油气钻探中发现了高含CO₂气的天然气气藏。对CO₂气稳定碳同位素、伴生稀有气体氦和氩同位素进行了分析研究，结果显示，福山凹陷CO₂气稳定碳同位素偏重，(13C_CO2为-5.01～-10.08‰，绝大多数样品大于-7.0‰，为无机成因CO₂气特征；伴生稀有气体氦同位素³He/⁴He值为(4.74~5.03)×10^-6，R/Ra值为3.38～3.59；伴生稀有气体氩同位素⁴⁰Ar/³⁶Ar值为1881～2190，也显示出幔源或壳幔混合CO₂气的特征。综合判定认为，福山凹陷CO₂为壳幔混合成因。始新统流沙港组岩浆岩体分布特征与CO₂气藏分布范围基本一致，也表明幔源-岩浆可能是福山凹陷CO₂气的主要来源。与南海北部边缘盆地其它地区如珠江口盆地西部、琼东南盆地东部CO₂气成因一致，都为幔源-岩浆来源，或壳幔混合来源。     

含硫化氢气井钻井过程中的腐蚀因素与防护研究

在含硫气井的钻井过程中对于HRC大于22的钻具钢材除了腐蚀疲劳之外，在pH值小于9的环境中会发生硫化物应力腐蚀破裂，这种破坏比腐蚀疲劳更突然、更快，使钻杆大量损坏。含硫气井在钻井过程中，由于湿硫化氢的出现，常常会出现油管、套管、钻井设备、钻井仪器以及对支持保护管柱的水泥环柱等腐蚀和损坏问题，为此，阐述了湿硫化氢的腐蚀特点、机理，归纳总结了影响腐蚀的因素，综述了如何在这些方面防止其腐蚀，使损失减小，为指导油管、套管防腐工程实践提供了依据。建议在钻井过程中采用碱性钻井液，其pH值可到9或更高(至pH值12)，以减缓或防止钻井过程中电化学从硫化物应力腐蚀破裂；含硫气井用的钻杆应该间歇使用。钻杆停用堆置时间可使其放氢，使钻杆恢复韧性，防止硫化物应力腐蚀断裂。     

光电设备电子机柜布线工艺研究

作为信号和电能载体的导线，同时也是噪声的载体和外来噪声侵入设备的媒体。描述了噪声通过导线侵入设备内部的方式，通过降低噪声的途径确定了机柜布线的原则，介绍了布线的要求和方法，最后提出了用布线槽布线的建议。     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

Optimal Control of the Primary Drying Stage of Freeze Drying of Solutions in Vials Using Variational Calculus

The problem of operating freeze drying of pharmaceutical products in vials placed in trays of a freeze dryer to remove free water (in frozen state) at a minimum time was formulated as an optimal control problem. Two different types of freeze dryer designs were considered. In type I freeze dryer design, upper and lower plate temperatures were controlled together, while in type II freeze dryer design, upper and lower plate temperatures were controlled independently. The heat input to the material being dried and the drying chamber pressure were considered as control variables. Constraints were placed on the system state variables by the melting and scorch temperatures during primary drying stage. Necessary conditions of optimality for the primary drying stage of freeze drying process in vials are derived and presented. Furthermore, an approach for constructing the optimal control policies that would minimize the drying time for the primary drying stage was given. In order to analyze optimal control policy for the primary drying stage of the freeze-drying process in vials, a rigorous multi-dimensional unsteady state mathematical model was used. The theoretical approach presented in this work was applied in the freeze drying of skim milk. Significant reductions in the drying times of primary drying stage of freeze drying process in vials were obtained, as compared to the drying times obtained from conventional operational policies.     

牛奶加工过程中的清洗(二)

五．牛奶厂的清洗。目前，牛奶厂采用的清洗方式主要是CIP清洗(Cleaning in place)，原地清洗或称定置清洗，即在基本不拆卸或挪动机械装置和管线的情况下对生产过程中能与牛奶发生接触的设备表面进行的清洗。其冲刷、清洗、灭菌的整个过程全部实现了自动化因此大大降低了劳动强度。而有一些不     

套保稠油油田火烧油层可行性分析

从火烧油层的筛选标准、实际地质条件及室内物理模拟实验入手，对该油田火烧可行性进行了分析。分析结果认为，套保油田进行火烧总体上是可行的，在实际火烧时应避开底水的影响，火烧区域应选在构造高部位或仅烧其主力层。     

加油站油品损耗的管理问题分析及解决办法

针对加油站在油品进、销、存方面因管理和人为作弊而产生的损耗大问题，提出了解决办法：各环节交接手续要严密完备；发货方实施保量运输，选择信誉好的承运方；在销售、储存方面应加强管理，推行加油站计量员、账务员集中管理，主要账表电子表格化，及时上报主管部门，执行责任追究制并与效益工资挂钩。