HEAT TRANSFER IN PARTIALLY MISCIBLE TERNARY SYSTEMS

In the study of mass transfer between partially miscible liquids, temperature perturbations have been found to have an important effect in the generation of interfacial activity. Micro- and macro-generated interfacial convection usually occurs in combination with one another even in fairly simple heat or mass transfer events. These combinations are responsible for the enhancement of mass transfer rates. In an effort to acquire a better understanding of the heat transfer effects in ternary liquid-liquid systems, temperature difference profiles were measured when contacting two partially miscible phases. A vertical and a rotational transfer cell were designed to contact the partially miscible phases without inducing external disturbances. Five thermocouples were immersed in the bottom liquid phase at predetermined positions below the interface. In order to understand the influence of the convection generated, the vertical cell was designed to hinder convection in one phase, while the rotational cell permits convection in both phases. The experimental results showed larger temperature differences in the rotational cell after the contact of the phases. Also, systems which were initially unsaturated presented larger heat effects than those in which the partially miscible solvents were initially saturated. Several parameters indicating the importance of heat effects in the ternary systems studied are reported.     

Thermal Shock Failure in Thick Epoxy Coatings

In this paper we describe an apparatus for reproducibly measuring thermal shock resistance of thick polymer layers bonded to metals. The thermal shock behavior is discussed in terms of epoxy samples bonded to an aluminum substrate. It was found that both high resin toughness and low resin thermal expansion coefficient improved thermal shock resistance of thick coatings, but only a sample containing 60wt. % glass beads did not develop a failure crack. Effects of sample thickness, temperature gradient, and resin composition on thermal shock behavior are discussed.     

工艺参数对PP挤出发泡泡孔结构的影响

研究了螺杆转速、机头口模形状以及机头温度对挤出发泡聚丙烯(PP)泡孔结构的影响。结果表明：在挤出发泡过程中，一定配方、机头形状和温度下，螺杆转速存在最佳值；机头形状越有利于建立高压，制得的泡沫的泡孔越细密均匀且发泡倍率越高；机头口模温度在保证顺利挤出情况下．越低越有利于制得高发泡倍率的泡沫。     

Security concepts for the dynamics of autonomous vehicle networks

The secure operation of autonomous vehicle networks in the presence of adversarial observation is examined, in the context of a canonical double-integrator-network (DIN) model. Specifically, we study the ability of a sentient adversary to estimate the full network’s state, from noisy local measurements of vehicle motions. Algebraic, spectral, and graphical characterizations are provided, which indicate the critical role of the inter-vehicle communication topology and control scheme in achieving security.     

成形压力对氧化铝瓷球性能的影响

本文以不同的压力等静压成形瓷球，研究了成形压力对瓷球烧结温度、密度及耐磨性的影响。结果表明：在本研究系统内随着压力的增加瓷球的烧结温度下降，烧成温度范围拓宽。采用150MPa成形的瓷球密度最大且耐磨性最好。     

Tensile Stress Relaxation of Alumina at High Temperature

The development of a tensile testing methodology for ceramics which enables a stress vs strain-rate response to be measured at high temperature is described. The test involves a carefully controled stress relaxation test at constant total strain using an experimental procedure and phenomenological analysis previously developed for metallic materials. It is demonstrated here with preliminary tests on alumina at 1050° and 1150°C. This offers, with further development, the possibility of establishing design stresses associated with low strain-rate behavior for structural applications. The results demonstrate that data covering four decades of strain rate may be generated in tests lasting a few hours. The inelastic strain consists of substantial anelastic recoverable strain in addition to a permanent creep strain.     

浅析SRT-Ⅳ裂解炉炉管弯曲及断裂原因

主要分析计算了裂解炉炉管受力情况，进而得出结论：裂解炉自身结构的相互约束力和炉管渗碳是导致炉管弯曲、断裂的主要原因，并提出了相应的解决措施。     

冷却器盘管失效分析及防范措施

本文介绍了冷却器盘管破裂泄漏的情况，分析了失效破坏的原因，并提出防止冷却器盘管破裂泄漏的措施。     

MgO／Ni系梯度功能材料的设计与制备

对ＭｇＯ／Ｎｉ系梯度功能材料（ＦＧＭ），分别用实验和微观力学模型测定和计算了用于热应力缓和设计的各物性参数。讨论了两种结果之间存在差异的原因。用有限元方法模拟了制备过程中ＦＧＭ的热应力，得到ＭｇＯ／Ｎｉ系ＦＧＭ的综合设计准则。按设计结果进一步调整粉末工艺性质，成功地烧制出ＭｇＯ／Ｎｉ系ＦＧＭ。     

污泥中总磷测定方法的探讨

污泥样品与氢氧化钠熔融,使污泥中含磷有机化合物全部转化为可溶性的正磷酸盐,然后测定污泥中的总磷含量.此方法方便易行,平行性好,准确度高,可作为测定污泥中总磷的标准方法.