反倾岩质边坡弯曲倾倒-剪切滑移破坏分析方法研究

目前反倾岩质边坡弯曲倾倒破坏分析方法仍以基于极限平衡理论的悬臂梁模型为主,但大多未考虑坡脚岩层的剪切破坏。为准确评价该类边坡的稳定性,建立考虑坡脚岩层剪切破坏的分析计算方法。首先,根据岩层变形破坏特征,将边坡分为后缘稳定区、中部弯曲倾倒区和前缘剪切区3个区域;其次,建立弯曲倾倒-剪切滑移破坏模式的稳定性分析方法;最后,通过工程实例验证,并进行参数分析。研究结果表明:提出的分析方法与工程实际符合性较好;边坡在倾角较陡、坡角较大时稳定性最差,坡角对边坡稳定性影响大于岩层倾角的影响;岩层厚度及层面内摩擦角增加有利于边坡稳定性,且会扩大坡脚剪切区范围。研究成果对反倾岩质边坡破坏的防治具有实践指导意义。     

基于PR控制器的直接转矩控制策略研究

针对传统直接转矩控制中采用开关表控制造成转矩和电流脉动,以及传统调节器不能实现对交流输入信号的无静差控制等问题,基于电机空间电压矢量的转矩和磁链2个分量解耦的控制方式和PR控制器能够在静止坐标系下实现对交流输入信号的无静差控制,将PR控制器用于永磁同步电机的直接转矩控制中,并由此设计出磁链和转矩的双PR控制器。同时,在定子磁链的观测中,采用基于转子位置和定子电流的新型定子磁链估计方法。试验结果证明,将PR控制器对交流输入信号的无静差跟踪特性应用于基于空间电压矢量调制的直接转矩控制中,系统能获得优良的动态和静态响应,取得了显著的应用成效,由此验证了所提方法的正确性和可行性。     

The importance of the compression test procedure for plastic drums for dangerous goods

Packagings for the transport of dangerous goods are tested by four tests:- free fall, leakproofness, hydraulic pressure and stacking. However, the test procedures can be interpreted in different ways, particularly the stacking test. Some test authorities apply a guided load to the top of the package and others, including the LNE in France, use non-guided loads. The objective of recent research carried out at LNE was to evaluate the risk (in terms of stack stability for dangerous goods packagings) if the stacking tests are performed with guided loads rather than non-guided loads. The stacking tests were carried out on a limited number of plastic drums (200 of four types) submitted for qualification testing using the above four tests, with either guided or non-guided loads. From the results we conclude that:

• i for the transport of dangerous goods of Danger Group I, the field of use is not altered when tested by either procedure.
• ii with goods of Danger Groups II and III, the use of either procedure does not alter the position as far as transport is concerned. However, there is a risk in warehousing: the non-guided procedure being preferred.

     

An enhanced,acoustic emission-based,single-fiber-composite test

In the single-fiber-composite (SFC) test, a fiber imbedded in a matrix is loaded in tension, resulting in a fragmentation of the fiber. In the conventional version of this test, the final fiber fragmentation length distribution is used with a micro-mechanical model to determine the average fiber/matrix interfacial shear stress. In the enhanced version of this test, one also determines the applied stress at each fiber fracture, and from this, one can evaluate the strength of the fiber at short gage lengths. In our measurement system, we utilize an acoustic emission (AE) technique to detect the fiber fractures and to locate the fiber breaks and so determine both the fiber failure stresses as well as the fiber fragmentation lengths while the test is in progress. Critical to the success of this test is a broadband AE system that utilizes point-like AE sensors, procedures for evaluatingin situ, the wavespeed of the first wave arrival and signal processing techniques for determining the arrival time of this signal as precisely as possible for a broad range of wave shapes. Here we describe the application of such an enhanced SFC test procedure to investigate the failure of a Nicalon fiber in an epoxy matrix.     

基于剪切带扩展法的海底斜坡稳定性分析

简介剪切带扩展法（SBP）的原理及其在海底滑坡稳定性分析的应用;以舟山六横岛典型海底斜坡为分析案例,开展基于高斯函数的SBP和极限平衡法（LEM）斜坡稳定性对比分析研究;进行SBP输入参数对剪切带扩展系数R的敏感度分析. 研究结果显示,对于斜坡剪切带破坏长度,当剪切带扩展系数R不大于1时,LEM与SBP得到的滑坡滑裂面区域一致,当R大于1时,SBP计算得到的最终滑动区域比LEM计算得到的区域大;在斜坡发生滑动破坏区域SBP比LEM计算得到的安全系数低;地震影响因素和土体特征位移对R的影响较大.     

STUDY ON THE VARIATION MECHANISM OF CARBON CONTENT OF LIQUID IRON IN MELTING GASIFIER

This paper studied the changing principles of carbon content in direct reduction iron (DRI) and liquid iron in the COREX melting gasifier. Under the normal working conditions of experimental equipment, liquid nitrogen was poured into the melting gasifier from its tuyere to cool down quickly. And then seven cross sections were made to study the carburization reaction and its characteristics of the solid iron and the liquid iron, and also the reaction of carbon between the slag and the metal. According to the results, the influences of the thickness of the semi-coke layer and the temperature on the carbon content of liquid iron in the COREX melting gasifier were confirmed.     

磷石膏提质降杂实验研究

磷石膏的综合利用对保护环境、促进企业可持续健康发展具有重要意义,但是磷石膏中的磷、氟、二氧化硅等杂质影响其利用。针对云南磷石膏中二氧化硅含量高的问题,采用正浮选工艺开展了磷石膏提质降杂的实验研究。通过单因素条件实验获得了合适的工艺参数：浮选温度为15 ℃、矿浆pH为2、十二胺用量为300 g/t。在此条件下,进行了“一粗二精”的正浮选开路流程实验,获得了二水石膏（CaSO₄·2H₂O）质量分数为97.5%、二氧化硅质量分数为1.17%的精矿,所得精矿达到了GB/T 23456—2018《磷石膏》一级品指标的要求;二水石膏回收率为98.58%、二氧化硅去除率为92.23%。通过正浮选不仅成功实现了二水石膏和二氧化硅的有效分离,而且磷石膏中的水溶磷和水溶氟也得到了有效去除,从而提高了磷石膏的品质。     

Effect of ammonia concentrations on SCC of α-brass under mode III loading

Stress corrosion cracking (SCC) of α-brass in ammonia solution was studied under mode III loading. The results showed that SCC occurred on the principal stress planes where shear stresses are zero. No SCC occurred on the maximum shear stress plane. Ammonia concentration affected fracture behaviour. When the concentration was low, many cracks with spacing of 10–150 μm were found on 45 ° planes, i.e., the principal stress planes. When the concentration was high, the cracks on 45 ° planes were not clearly visible because of serious general corrosion.     

TA2／A3爆炸复合界面微观断裂机制的SEM原位研究SCIEI

借助ＳＥＭ对ＴＡ２／Ａ３爆炸复合界面（包括细小波状界面，中波界面及具有再入射流熔块的大波界面）的微观断裂机制进行了动态研究。结果表明，爆炸复合界面微观断裂机制是：微裂纹在波头夹杂或再入射流熔块内及熔块和基体界面处萌生，并在裂尖应力场作用下沿与外载垂直方向扩展。同时，沿ＴＡ２／Ａ３界面产生微裂纹并在外载作用下，相互连接而扩展。