水溶性防氧化剂在SMT用印制板上的应用

水溶性的防氧化剂是一种有机可焊性保护剂。其方法是在印制板完全阻焊、字符层的印刷，并经电检之后，通过表面浸渍在裸铜的贴片位或通孔内形成一种耐热性的有机可焊性膜层。这种有机、可焊、耐热的膜层，膜厚可达0.3-0.5mm，其分解的温度可达约300℃，传统的印制板的热风整平法亦无法满足QFP愈来愈密集的需求，同时也无法满足SMD表面平整度的要求，更无法适应PCB薄型化生产。烷基苯并咪唑的OSP法能弥补这项缺陷，因而在PCB业乃至SMT产业中得到了广泛的应用。     

控制棒驱动机构常温通风均匀性试验研究（续篇）

本文叙述控制棒驱动机构在常温通风均匀性方面的试验。通过平顶型堆顶结构和球面型堆顶结构通风均匀性试验的比较,找出通风的阻力、风速和不均匀系数间的规律。     

7-羟基全氢化噁唑并噁嗪鞣剂的合成及其鞣性研究

报导了新型鞣剂 7-羟基全氢化唑并嗪 (以下简称 OX- Z)的合成方法。试验确定合成的最佳条件为 :在氮气保护下 ,将等摩尔量的二乙醇胺在 10℃水浴中缓慢滴入乙二醛中 ,滴加时间 0 .5 h,在 2 0℃水浴中继续反应 1.5 h,产率为 6 2 .9%。 OX- Z对浸酸绵羊皮单独鞣制 ,可使收缩温度升高到 87℃。最佳鞣制条件为 :p H10 .0 ,OX- Z用量 5 % ,鞣制时间 8h。在对 OX- Z与皮胶原的结合类型的研究中证明它们之间是以化学键结合的。     

Asymmetric Hydrogenation of Activated Ketones on Platinum: Relevant and Spectator Species

The heterogeneous enantioselective hydrogenation of activated ketones over chirally modified platinum is reviewed with emphasis on identifying the role of the various species observed in this catalytic system. The past years have witnessed a continuous broadening of the scope of this catalytic system including new reactants and modifiers affording over 97% ee. New reaction pathways have been uncovered and the kinetic and mechanistic studies have been faced with a number of complicating factors caused by spectator species and interactions in solution and on the Pt surface. The previously proposed mechanistic models are critically assessed in the light of these new findings.     

伊朗德黑兰地铁轨道施工方法

依托伊朗德黑兰地铁一、二号线工程 ,针对地铁单洞单线采用的轨道施工轨排法存在的不足 ,根据单洞双线隧道的特点 ,提出了利用组装好的轨排直接铺设在隧道结构底板上作为轨道平板车临时轨道的施工新方法     

开关稳压电源用铝电解电容器的失效机理

概述了开关稳压电源用铝电解电容器的工作状态和失效模式，着重讨论了开关稳压电源用铝电解电容器的开路失效和击穿失效机理。     

Oracle9i数据库安全管理机制剖析

数据库安全和数据安全机制是数据库开发设计者目前必须考虑的问题之一。Oracle9i数据库管理系统在数据库安全方面为数据库管理员和应用开发者提供了很好的安全机制。文章从不同侧面和角度讨论Oracle9i数据库系统的安全管理机制，为实施更安全更灵活的数据库安全策略提出了全方位的技术思路。     

碳/碳复合材料CVI工艺中热解碳形成机理的研究

对碳碳复合材料CVI或（CVD）工艺中热碳组织的类型，沉积机理等研究情况进行了简要的综述，并对其进一步研究提出了相应观点。     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

絮凝剂品种对水下不分散混凝土性能影响的比较

通过电荷中和、吸附架桥和表面吸附分析了絮凝剂作用机理 ,运用絮凝机理进一步分析了絮凝剂在水泥体系中的作用以及絮凝剂对流动度的影响 ,从而对掺加JHP (纤维素类 )和Pj (丙烯类 )絮凝剂的水下不分散混凝土性能作了综合比较。掺Pj絮凝剂的混凝土 ,其坍扩度损失大 ,抗分散性能不如掺JHP絮凝剂的好 ;掺JHP絮凝剂的混凝土坍扩度在 3h内损失很小