Feasibility analysis of membrane reactors – discovery of reactive arheotropes

A feasibility analysis methodology adopted from reactive distillation is applied to membrane reactors. A model is formulated to depict the reactive liquid phase composition on the retentate side of a continuous type membrane reactor. The effects of both the chemical reaction kinetics and the membrane mass transfer kinetics on the feasible products are elucidated by means of retentate phase diagrams and bifurcation analysis. The proposed method can be applied to various membrane processes, independent of the specific structure of the membrane. Two quaternary reaction systems are considered to illustrate the methodology. In the first hypothetical system, it is shown how selective membranes can influence the sequence of effective volatilities which in turn affects the feasible products of the system. In the second example of practical importance, i.e. the heterogeneously catalysed synthesis of propyl acetate coupled with permeation through a porous polycarbonate membrane, the dusty gas model is applied to describe the component fluxes through the membrane. For the latter reaction system, the existence of reactive arheotrope is demonstrated. Arheotropes represent mass transfer controlled feasible products of membrane separation process.     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

基于DELPHI的镍氢电池管理系统软件设计

通过对镍氢电池性能的研究，给出了一个应用ISA总线技术构建的、基于DELPHI编程平台的镍氢电池管理系统的设计方案，重点介绍了该系统的软件技术和实现方法。     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

Expressive Facial Gestures From Motion Capture Data

Human facial gestures often exhibit such natural stochastic variations as how often the eyes blink, how often the eyebrows and the nose twitch, and how the head moves while speaking. The stochastic movements of facial features are key ingredients for generating convincing facial expressions. Although such small variations have been simulated using noise functions in many graphics applications, modulating noise functions to match natural variations induced from the affective states and the personality of characters is difficult and not intuitive. We present a technique for generating subtle expressive facial gestures (facial expressions and head motion) semi‐automatically from motion capture data. Our approach is based on Markov random fields that are simulated in two levels. In the lower level, the coordinated movements of facial features are captured, parameterized, and transferred to synthetic faces using basis shapes. The upper level represents independent stochastic behavior of facial features. The experimental results show that our system generates expressive facial gestures synchronized with input speech.     

论剪切质量的提高

通过对飞剪剪切长度，精度，剪刃间隙和压板机构等参数的优化，来提高钢板的剪切质量。     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

基于显微视觉的宏/微双重驱动微动台的自动标定

提出了基于压电技术的微操作系统的自动标定方法,采用混合式步进电机直接驱动的宏动平台,实现系统大行程宏动定位,安装在宏动平台上的压电陶瓷驱动的微动平台和精密光栅,实现亚微米级的分辨率和定位精度,通过以上两部分实现定位机构的全闭环反馈控制,采用显微视觉反馈获取微动台操作器在图像中的位置信息进行标定。实验结果表明:系统的动态和稳定性能良好,自动标定运算速度快,运行速度达到11 frame/s,实现了对系统的精确标定,标定精度达到0.1μm。     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

Analysis of Multiphase Flow and Heat Transfer: Pressure Buildup in an Unsaturated Porous Slab Exposed to Hot Gas

This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab.