济钢中板厂加快技术创新的对策

本文通过对中板厂近年来技术改造后工艺装置和技术水平的分析，并结合中国加入WTO后对中国钢铁企业面临全球化市场竞争严峻性的认识，提出了中板厂在实现高产生产模式后，应加快技术创新的步伐，尽快完成由高产向优质、多品种、低消耗的高效化生产模式转化的主导思想、措施及建议。     

Dynamic analysis and drilling degrees of freedom

Finite element methods for dynamic analysis employing elements with drilling degrees of freedom are presented. The formulation is based on a variational principle in which displacements and rotations are interpolated independently. The issue of zero masses corresponding to rotational degrees of freedom is addressed and techniques for defining consistent and lumped rotational mass matrices are presented.     

Evaluation of a system of wind tunnels for field studies of ammonia loss from grassland through volatilisation

Rates of ammonia (NH₃) loss from a ryegrass sward measured using a system of small wind tunnels were compared with concurrent measurements made using a micrometeorological mass balance method. Measurements were made during two experiments within a circular plot (radius 10m) treated with urea at a rate of 200kgNha^?1. In the first experiment, air speed through the tunnels was adjusted as necessary to maintain a value of approximately 1ms^?1. This value differed on most occasions from the mean ambient wind speed which was measured at a height of 250mm and which ranged from 0.61 to 2.95ms^?1. Rates of loss measured using the wind tunnels differed by a factor of between two and five from those measured using the mass balance method; there was no consistent pattern in the differences between the rates of loss. The total losses of NH₃ measured during 15 days were equivalent to 49.1 and 30.2kg Nha^?1 for the mass balance and wind tunnel methods, respectively. In the second experiment, air speed through the tunnels was adjusted as necessary to maintain a value as close as possible to the mean ambient wind speed measured at a height of 250mm. Rates of NH₃ loss measured using the two methods did not differ significantly; total losses of NH₃ during 17 days were equivalent to 96.9 and 101kg Nha^?1 for the mass balance and wind tunnel methods, respectively. The difference between the findings of the two experiments could be attributed to the direct effect of air speed through the tunnels rather than to differences between ambient temperatures and those inside the tunnels. During and following periods of rain the rates of loss measured using the tunnels were up to six times greater than those observed with the mass balance method. Rates of loss measured by the two methods became similar again when the tunnels were moved following rain. The study demonstrates that enclosures can be designed and operated to provide reliable measurements of the rate of NH₃ loss from grassland. Potential applications of the two methods are discussed.     

Evaluation of the reactivity of titanium with mould materials during casting

A methodology for evaluating the reactivity of titanium with mould materials during casting has been developed. Microhardness profiles and analysis of oxygen contamination have provided an index for evaluation of the reactivity of titanium. Microhardness profile delineates two distinct regions, one of which is characterised by a low value of hardness which is invariant with distance. The reaction products are uniformly distributed in the metal in this region. The second is characterised by a sharp decrease in microhardness with distance from the metal-mould interface. It represents a diffusion zone for solutes that dissolve into titanium from the mould. The qualitative profiles for contaminants determined by scanning electron probe microanalyser and secondary ion mass spectroscopy in the as-cast titanium were found to be similar to that of microhardness, implying that microhardness can be considered as an index of the contamination resulting from metal-mould reaction.     

On the improvement of detection characteristics of trans-stilbene crystals by improving crystal perfection

Organic molecular scintillating crystals are noted for their good timing and particle discrimination process. Trans-stilbene is one such candidate noted for its good particle detection characteristics for the past five decades. Progressive strengthening of detection characteristics of trans-stilbene has been attempted by improving crystal perfection. A series of timing resolution studies have been carried out for the Bridgman grown trans-stilbene crystals under different experimental conditions. The results were compared with the previously reported values. Pulse shape discrimination process has been carried out for ²⁴¹Am and ²⁵²Cf sources and good discrimination has been obtained for gamma-alpha and gamma-neutron sources from the grown organic phosphor crystal. Electronic Publication     

热力除氧器运行特性实验研究

在热力除氧器实验装置上，对研制的新型除氧器进行了稳态运行特性和动态运行特性实验，得到了除氧器的各种运行特性曲线。研究结果表明，由于对喷嘴和填料进行改进，建立起有利于除氧的传热传质条件，使所研制的除氧器具有良好的稳态及动态运行特性，除氧效果优良。     

MODELING LIQUID MASS TRANSFER IN HIGEE SEPARATION PROCESS

Correspondence concerning this paper should be addressed to Professor Richard S.H. Mah. Hsien-Hsin Tung is now affiliated with Department of Chemical Engineering, California Institute of Technology

Penetration theory is used to describe the liquid mass transfer in Higee separation process. Within a possible range of effective areas, it is shown that the predicted mass transfer coefficients are in reasonable agreement with the estimated mass transfer coefficients. The estimated coefficients were calculated from the experimental data and the possible effective areas. Hence it is concluded the penetration theory is generally applicable to describe liquid mass transfer in Higee separation process. The comparison also suggests that liquid mixing at the junctions of packing materials may be more complete in Higee process than in traditional process.     

Mechanical and thermal properties of HVOF sprayed Ni based alloys with carbide

The objective of the present study is to develop multi-functioned coating to the components, which are made of copper with electroplated Ni and are widely used for steel making industry. In this paper, we report the mechanical and thermal properties of Ni based superalloys with carbide sprayed by high velocity oxygen fuel (HVOF), and the detailed effects of sprayed material, spraying conditions, and initial powder structure on these properties. It was found that, among commercial Ni self-fluxing alloys (without fusing treatment), coating with a carbon content of 0.58 mass% had the most preferable properties, with a good balance of the hardness, strength, and thermal shock resistance. The thermal shock resistance depended not only on the strength of the coating but also on the volume contraction when tested at high temperatures. For the several developed Ni based superalloys with carbide, Ni20Cr8Mo5Fe–WC and Ni16Cr15Mo3–WC demonstrated the prominent adhesion strength and thermal shock resistance with high Galvanic corrosion resistance through optimized spraying condition. Also, 20 mass% NiCr–Cr₃C₂ coating sprayed by using employed relatively small primary particle succeeded in achieving the multi-superior properties; high adhesion strength, high corrosion resistance and thermal shock resistance.     

载人航天高可靠伺服技术

回顾了载人航天高可靠伺服技术的研制道路，介绍了用于载人航天火箭推力矢量控制中的新型三余度伺服机构的技术特点，对载人航天伺服技术的未来发展进行了分析和展望。     

带有集中质量的分布质量弹性转动横振精确解

求得了带有集中质量的分布质量弹性转轴系统横向自由振动的频率方程和振型函数的精确解析表达式，及其与不转动轴系统自由振动的频率方程和振型函数及转动角速度之间的精确解析关系