The interfacial microstructure of joined single crystal and polycrystalline alumina

The interfacial microstructures of 96 and 98% polycrystalline alumina joined with single crystal sapphire have been investigated in relation to the joining parameters. Joining has been evaluated based on either using a thin spin-on silica interlayer or by placing the alumina and sapphire in direct contact. The materials were joined by placing the coated or uncoated surfaces in contact and heating in the range of 1340–1475 °C with minimum external load. With the aid of a silica interlayer, sapphire and 98% polycrystalline alumina were successfully joined in 180 min at 1400 °C and above, while samples without a silica interlayer failed to join under these conditions. However, sapphire and 96% polycrystalline alumina were joined both with and without the use of silica interlayer. A variety of interfacial morphologies have been observed, including amorphous regions, fine crystalline alumina, and intimate contact between the sapphire and polycrystalline alumina.     

Porous elastomeric beads from crosslinked emulsions

The production of porous polymeric particles is attractive for a large number of applications and can be achieved by various techniques. Although numerous production schemes exist for glassy polymers, difficulties arise for soft, rubbery materials that need a chemical crosslinking step, such as elastomers. This is particularly true for poly(dimethylsiloxane) (PDMS), which shows the lowest glass‐transition temperature among the polymers. Recent studies suggest in situ hydrogen bubble formation or vacuum drying of water droplets dispersed in the polymer matrix in order to generate porous PDMS structures. In this work we report early results based on the chemical crosslinking of water in PDMS emulsion droplets in a mechanically stirred thermostated water vessel. This approach is shown to lead to high porosity PDMS beads (ca. 10^?3 m particle diameter) with an open structure whose properties (diameter and porosity) are strongly influenced by the starting composition (solvent, surfactant, and polymer types and ratios), as well as the operating parameters (agitation and temperature). The possible uses of these derived beads are discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 967–971, 2002     

Interfacial tension between coexisting polymer solutions in mixed solvents and its correlation with bulk thermodynamics: phase equilibria (liquid/gas and liquid/liquid) for the system toluene/ethanol/PDMS

Vapor pressures, phase equilibria and interfacial tensions σ were measured for solutions of poly(dimethylsiloxane) (PDMS, M_w[equals]75 kg/mol and M_n[equals]50 kg/mol) in mixed solvents of toluene (TL) and ethanol (EtOH) at 30, 40, 50 and 60 °C. The experimental ternary phase diagrams can be modeled quantitatively from the determined concentration and temperature dependent binary interaction parameters χ_ij if the experimentally inaccessible composition dependence of χ_EtOH/PDMS is adjusted. The relations between σ and the equation of state of the system differ from that applying to single solvents. The exponents as well as the amplitude prefactors of the corresponding scaling laws (e.g. the dependencies of σ on the length of the tie lines or on the hump energy, i.e. on the intrusion into the two phase regime quantified in terms of Gibbs energies) change considerably with temperature. However, this variation can be reduced significantly by normalizing the independent variables. Dividing the length of the tie lines by the length for the corresponding binary subsystem proves more efficient than the distance of these tie lines from the critical point of the ternary system relative to the maximum distance of the binary subsystem. A combined normalization does not improve the situation.     

含氟聚酰亚胺的辐射交联及其交联度的XPS表征

含氟聚酰亚胺(FPI)是一种耐高温、耐水解的新型聚酰亚胺。到目前为止,尚未见文献报道它的辐射交联。本文发现它能在高温辐射下交联,交联后的含氟聚酰亚胺的玻璃化转变温度以及高温力学性能有明显提高。本文还首次用XPS方法做了它的交联度表征。用XPS方法求得FPI的凝胶化剂量为50Mrad。     

MODELING LIQUID MASS TRANSFER IN HIGEE SEPARATION PROCESS

Correspondence concerning this paper should be addressed to Professor Richard S.H. Mah. Hsien-Hsin Tung is now affiliated with Department of Chemical Engineering, California Institute of Technology

Penetration theory is used to describe the liquid mass transfer in Higee separation process. Within a possible range of effective areas, it is shown that the predicted mass transfer coefficients are in reasonable agreement with the estimated mass transfer coefficients. The estimated coefficients were calculated from the experimental data and the possible effective areas. Hence it is concluded the penetration theory is generally applicable to describe liquid mass transfer in Higee separation process. The comparison also suggests that liquid mixing at the junctions of packing materials may be more complete in Higee process than in traditional process.     

中原高温高盐油藏疏水缔合聚合物凝胶调剖剂研究

针对中原油田高温(>80℃)、高盐度(>50 g/L)、高硬度(>1 g/L)砂岩油藏,研制了地下成胶的高热稳定性聚合物凝胶调剖剂。所用聚合物为疏水缔合聚合物AP-P4,M=9.0×106,HD=27%,疏水基摩尔分数0.2%;交联剂为可生成酚醛树脂的3种化合物;调剖剂胶液用矿化度160 g/L的马寨油田污水配制;实验温度95℃。根据形成的凝胶黏度(95℃,1.1 s-1)确定交联剂各组分用量为:MZ-YL 0.429%,MZ-BE 0.060%,MZ-XS 0.012%;酸度调整剂用量0.12%;成胶时间10~15小时。2.5、3.0、3.5 g/L AP-P4的凝胶在95℃老化100天后黏度保持在~40 Pa.s及以上。初配制胶液在3000 r/min下剪切15分钟后黏度降低87.5%~89.0%,但成胶后和老化过程中凝胶黏度只比未剪切样降低17.1%~6.6%。3.5 g/L AP-P4的调剖剂对~1μm2的6支储层岩心的堵塞率在88.1%~95.8%范围,平均93.3%,造成的残余阻力系数在15.2~28.6范围,平均19.8,使渗透率级差2.3~8.0的4组双人造岩心的注水流量比发生不同程度的反转。认为该凝胶调剖剂高温下稳定性好的原因,是强化学交联密度低,因而凝胶脱水收缩作用弱。图2表5参5。     

Mechanical properties and antibacterial activity of peroxide‐cured silicone rubber foams

Silicone rubber (SR) foams were prepared by the peroxide curing of a silicone compound with 2,4‐dichlorobenzoyl peroxide (DCBP), di‐t‐butyl peroxide (DTBP), or 2,5‐dimethyl‐2,5‐di(t‐butylperoxy) hexane (DBPH) in the presence of 2,2′‐azobisisobutyronitrile (AIBN) as a blowing agent. The cells were formed in the foam as a result of nitrogen produced by the decomposition of AIBN during the foaming process. The cell size, hardness, and tensile properties of the SR foams were examined as a function of the peroxide concentration. When the peroxide concentration increased, the hardness and tensile strength of the SR foams increased, whereas the cell size and elongation at break decreased. The antibacterial activity of the prepared foams was also evaluated via their effects on Staphylococcus aureus and Escherichia coli. The peroxide‐cured SR foams had antibacterial activity because a toxic residue was generated by the peroxide decomposition. The foam prepared by the AIBN/DCBP system showed more antibacterial activity than the AIBN/DBPH and AIBN/DTBP ones. However, after postcuring at 250°C for 2 h, the antibacterial activity of the SR foams significantly decreased. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Dynamic photorheological analysis of photopolymerizable urethane dimethacrylate resins with varying diluent content and light fluence

The in situ measurement of dynamic changes in viscosity induced by illumination has been performed on a range of photosensitive urethane dimethacrylates (UDMA) evaluating the response at three different illuminations intensities (1, 2, and 5 W cm^?2) and at three different diluent concentrations (15, 30, and 50%), using 1,6‐hexanediol dimethacrylate (HDDMA). The initial viscosity value ranged between 1 and 10 Pa s for the mixtures with final viscosities approaching 1 × 10⁷ Pa s after illumination. The initial rise in viscosity was analyzed using an exponential model with an exponent ranging from 1.0 to 2.5 with time under exposure. Higher conversion rates were observed with both higher intensity and lower HDDMA content. The analytical approach taken here could aid in developing more sophisticated models that consider simultaneous flow and cure advancement in other thermosets. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polymer transcrystallinity induced by carbon nanotubes

In this work, we provide the evidence of polymer transcrystallinity in the presence of carbon nanotubes (CNTs). The interfacial morphology of carbon nanotube fiber-polypropylene matrix is investigated by means of polarized optical microscopy (POM), wide-angle X-ray diffraction (WAXD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The supramolecular microstructures of polypropylene transcrystals induced by the nanotube fiber are observed in the range of isothermal crystallization temperatures from 118 °C to 132 °C. The dynamic process of transcrystallization is analyzed by using the theory of heterogeneous nucleation. Microstructure analysis shows that the nanotubes can nucleate the growth of both α- and γ-transcrystal, and α-transcrystals dominate the overall interfacial morphology. Close to the nanotube fiber surface, a cross-hatched lamellar microstructure composed of mother lamellae and daughter lamellae is observed.     

Mechanism of heat transport in nanofluids

We have calculated thermal conductivity of alumina nanofluids (with water and ethylene glycol as base fluids) using temperature as well as concentration-dependent viscosity, η. The temperature profile of η is obtained using Gaussian fit to the available experimental data. In the model, the interfacial resistance effects are incorporated through a phenomenological parameter α. The micro-convection of the alumina nanoparticle (diameter less than 100 nm) is included through Reynolds and Prandtl numbers. The model is further improved by explicitly incorporating the thermal conductivity of the nanolayer surrounding the nanoparticles. Using this improved model, thermal conductivity of copper nanofluid is calculated. These calculations capture the particle concentration-dependent thermal conductivity and predict the dependence of the thermal conductivity on the size of the nanoparticle. These studies are significant to understand the underlying processes of heat transport in nanofluids and are crucial to design superior coolants of next generation.