浅埋地下建筑风冷热泵空调系统传热模型与试验研究

本文在浅埋地下建筑风冷热泵空调系统围护结构传热动态模拟的基础上，通过对南京市太园地下旅社围护结构传热的实时测试，验证动态传热模型及计算机模拟方法的可行性和正确性，为浅埋地下建筑风冷热泵空调系统的装机容量、节能指标和设计计算提供一定的理论依据。     

Heat transfer of a row of three butane/air flame jets impinging on a flat plate

Experiments were performed to investigate the heat transfer characteristics of a row of three premixed, laminar, butane/air flame jets impinging on a water-cooled flat plate. The between-jet interference was found to reduce the heat transfer rate in the jet-to-jet interacting zone due to the depressed combustion. The interference became stronger when the jet-to-jet spacing and/or the nozzle-to-plate distance were/was small. The positive pressure existed in the between-jet interacting zone caused the asymmetric flame and heat transfer distribution of the side jet. The meeting point of the spreading wall jets of the central and the side jets did not occur at the midpoint of the neighboring jets, but at a location shifted slightly outwards. The maximum local heat flux and the maximum area-averaged heat flux occurred at a moderate nozzle-to-plate distance of 5d with a moderate jet-to-jet spacing of 5d. The lowest area-averaged heat flux was produced when both the jet-to-jet spacing and the nozzle-to-plate distance were small. Comparing with a single jet under the same experimental conditions, the heat transfer rates in both the stagnation point and the maximum heat transfer point were shown to be enhanced in a row of three-jet-impingement system. The present study provided detailed information on the heat transfer characteristics of a row of three in-line impinging flame jets, which had rarely been reported in previous study.     

化学成分和固溶温度对1Cr17Mn9Ni4N不锈钢组织和性能的影响

为提高1Crl7Mn9Ni4N钢固溶处理后的力学性能(特别是钢的强度)，研究了化学成分及固溶处理温度对其组织和性能的影响。结果表明，1000—1125℃固溶处理后，该钢的组织为单相奥氏体。在标准成分范围内，随着镍、锰含量的增加，该钢的强度降低，塑性有所改善。氮明显提高该钢的强度。根据试验结果，每增加0．01％的氮钢的室温强度可提高大约5MPa，且塑性基本上不受影响。当合金成分(质量分数，％)控制在C0．08—0．12、Crl6．5—17．5、Ni3．5—4．2、Mn8．0—9．0、N0．22—0．28时，1Crl7Mn9Ni4N钢经1050—1100℃固溶处理后强度较高、塑性好，室温强度σ0．2和σb可分别达到400MPa和800MPa。     

Heat transfer mechanism of a swirling impinging jet in a stagnation region

Heat transfer characteristics of a swirling impinging jet have been experimentally examined using a combined particle image velocimetry (PIV) and laser‐induced fluorescence (LIF) technique for simultaneous measurement of velocity and temperature fields. The present study shows that the radial width of the jet stretches with increasing swirl intensity, and that the stretching phenomenon contributes to the maximum local heat transfer coefficient. At the stagnation region, the flow near the heated surface is mixed intermittently by reverse flows toward upstream, and spatial distributions of temperature are correlated with instantaneous velocity vector maps. The dynamic behavior of recirculation zones, attributed to swirl number Sw and impinging distance, mainly determines the turbulent heat transfer at the stagnation region. © 2003 Wiley Periodicals, Inc. Heat Trans Asian Res, 32(8): 663–673, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10120     

Hydriding and Dehydriding Characteristics of Mechanically Alloyed LaMg_(17) Ni Composite Material

Magnesiumandmagnesiumalloyshavebeenin vestigatedashydrogenstoragematerialsforseveralde cadesbecausefarmorehydrogenbyweightcanbestoredinthemthaninmostoftheothercurrentlyknownhydrogenstoragealloys .Moreover ,thehighnaturalabundanceofMg ,itslightmassandenviron mentalcompatibilitypotentiallymakemagnesiumoneofthemostprospectivecandidatesforfuturehydrogenstoragematerials .Unfortunately ,thepracticalappli cationofMganditsalloyshasbeenlimitedonlytocertainstoragedevicebecauseoftheirpoorhydriding dehydr…     

减四线馏分油的热容测定及热力学性质研究

测试了减四线馏分油低温热容 ,并进行了热重 /微分热重 (TG/DTG)和差示扫描量热 (DSC)分析。在 80～ 373K温区 ,用高精度全自动绝热量热仪测定了热容值 ,用最小二乘法对实验测量值进行拟合 ,建立了热容随温度变化的多项式方程。从减四线馏分油的热容曲线 ,发现该样品从固相变为液相 ,存在着两个熔化峰 ,分别为 2 94 .17K和 331.5 7K ,后者为熔化主峰。以此为熔点 ,计算出熔化焓、熔化熵分别为 88.19J/g和0 .2 6 6 0J/ (K·g)。从TG/DTG分析曲线发现该油样在 5 73K开始失重 ,到 6 6 3K失重速度达到最大 ,可能是由于样品蒸发引起。从DSC分析曲线 ,发现样品除 333K附近出现熔化吸热峰外 ,在 5 73K到 873K范围还出现一系列吸热峰 ,可能与样品的蒸发和热分解有关。     

链条锅炉的节能改造

本文针对株洲硬质合金厂SHL20—13—AII型20t蒸汽链条锅炉存在的问题，进行了节能改造，取得了显著的成效。     

模拟焊后热处理对锅炉用钢板SA-299力学性能的影响

对新日铁供货的SA-299钢板取样进行了供货状态及610～650℃/8h炉冷的模拟焊后热处理,以进行力学性能对比试验。试验结果表明,经过630℃/8h炉冷的模拟焊后热处理后σs降低25～40MPa、σb降低55～65MPa,但力学性能符合ASMESA-299标准和采购规程C1F19-98的要求。     

Question hard, answer simply: A comment on Storms et al. (2003).

It seems clear that, for whatever reasons, the dementia of the Alzheimer type patient group (as well as other patient groups) exhibits behavior that is different from the normal control group. G. Storms, T. Dirikx, J. Saerens, S. Verstraeten, and P. P. De Deyn (2003) rightfully argue that the observed behavior (similarity judgments) does not tell us the source (cause) of the differences between the 2 groups. Rather, the focus of the study should be placed more on finding the ways the 2 groups are different. They also point out various methodological problems in some of the previous attempts to characterize the nature of the differences. Further methodological issues in G. Storms et al.'s study are examined. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

铁通资源管理系统的设计和实现

在分析铁路通信资源结构的基础上,利用地理信息系统技术、数据库技术和客户/服务器(C/S)模式,为铁通(ChinaTietong)各级分公司和运营部门提供一套较为完善的资源管理信息系统。文中分析了铁通资源的结构与资源之间的关联,介绍了系统功能、物理结构及体系结构,详细分析了数据库设计、地理信息系统和系统安全性所采用的关键技术。这套系统的应用对铁通网络管理的现代化将起到重要的推动作用。