十万立方米储罐用高强钢SPV490Q的冬季焊接施工

通过对高强钢焊接性能的分析 ,提出了高强钢冬季焊接施工带来的问题及处理办法。可靠的焊前预热和焊后保温是确保冬季焊接施工质量的关键措施     

Subsecond thermophysics research at the Boris Kidrich Institute Vincha

In the early eighties, at the Boris Kidrich Institute Vincha, a method for measuring specific heat and electrical resistivity of electrical conductors in the millisecond resolution range was developed for measurements from room temperature to 1900 K. Over a period of nearly 10 years, the method was applied to different materials, including pure metals, ferrous, and nickel/ chromium alloys, and to the characterization of candidate materials for thermophysical property reference standards. This paper describes the method and reviews the results obtained in specific heat and electrical resistivity studies of ferromagnetic and other materials. The paper also demonstrates capabilities of the method for describing phase transitions or anomalies in pure metals (Fe, Co, Ni) or alloys (Nichrome, austenitic stainless steel).Paper presented at the Second Workshop on Subsecond Thermophysics, September 20–21, 1990, Torino, Italy.     

水泵水轮机的数值模拟及其应用

采用足够小的直线段拟合机组全特性曲线平直部分，采用二次多项式拟合机组全特性曲线弯曲部分，推导了有关方程，并对模拟的方程进行了处理，编制了较通用的计算机程序，利用该计算机程序对我国蒲石河抽水蓄能电站进行了计算分析，计算结果表明：该计算机程序计算速度较快、计算准确度较高，提出的水泵水轮机的数值模拟方法具有实用价值．     

冷却速度对激光相变组织分布的影响

提出通过改变边界换热条件，从而改变冷却速度，达到控制激光相变硬化。实验和计算结果的比较表明，这种控制相变及其组织分布的方法能够处理激光淬火难以解决的问题。     

响洪甸电站引水隧洞进口水下岩塞爆破施工

响洪甸抽水蓄能电站水下岩塞爆破施工要求高,技术新,难度大.由于施工准备充分,并进行了一系列材料及施工试验,工程进展顺利,排孔造孔、导洞药室开挖、药管与起爆体加工、装药与堵塞、网络施工、充水补气等工程施工质量符合设计要求,岩塞爆破准时成功起爆.     

Thermal characteristics of packed bed storage system

The thermal behaviour of a packed bed storage system charged with hot air is modelled using two partial differential equations representing the energy conservation in the air and solid phases constituting the bed. These two equations are coupled through the heat exchange process between the two phases. A fully implicit numerical scheme based on forward, upwind and central differencing for the time, first and second space derivatives, respectively, is used to solve the modelling equations. Marching technique is used for the air equation and a tri-diagonal matrix solver is employed to solve the solid equation. The solution yields the thermal structure of the bed, namely the air and solid temperature distribution inside the bed at any particular time, and the variation of total energy stored in the bed with time. The effect of bed length, solid diameter and void fraction on the thermal characteristics of the packed bed is studied. Further, the performance of the bed under variable inlet air temperature and mass flow rate is investigated.     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

高能超声处理Al-1Si合金凝固组织分析

采用高能超声处理Al-1Si合金熔体,借助金相显微镜和电子探针进行组织分析,并测定合金的熔化潜热,分析了熔体中超声空化效应和声流效应影响凝固过程的机理。结果表明,试样晶粒平均尺寸由超声处理前的94μm减小到超声处理后的34μm;合金试样的熔化吸热量由263.90J/g降低为159.81J/g,在熔体中施加高能超声显著改善了合金成分的均匀性并细化了晶粒。     

溶胶－凝胶二氧化硅驻极体薄膜的物理化学改性

实验研究了由溶胶－凝胶法制备二氧化硅驻极体薄膜的工艺。用红外透射谱、扫描电子显微镜以及驻极体等温表面电位测量和热刺激放电等实验考察了热处理和化学表面修正两个关键工艺对溶胶－凝胶二氧化硅样品驻极体性能的影响。结果表明经过高温条件下一定时间的热处理和化学表面修正，可以制备出性能优良的驻极体薄膜