Passive solar systems for heating, daylighting and ventilation for rooms without an equator-facing facade

Spaces without northerly orientations have an impact on the ‘energy behaviour’ of a building. This paper outlines possible energy savings and better performance achieved by different zenithal solar passive strategies (skylights, roof monitors and clerestory roof windows) and element arrangements across the roof in zones of cold to temperate climates typical of the central and central-southern Argentina. Analyses were undertaken considering daylighting, thermal and ventilation performances of the different strategies. The results indicate that heating, ventilation and lighting loads in spaces without an equator-facing facade can be significantly reduced by implementing solar passive strategies. In the thermal aspect, the solar saving fraction reached for the different strategies were averaged 43.16% for clerestories, 41.4% for roof monitors and 38.86% for skylights for a glass area of 9% to the floor area. The results also indicate average illuminance levels above 500 lux for the different clerestory and monitor arrangements, uniformity ratios of 0.66–0.82 for the most distributed arrangements and daylighting factors between 11.78 and 20.30% for clear sky conditions, depending on the strategy. In addition, minimum air changes rates of 4 were reached for the most extreme conditions.     

Circulation rates of boiling liquids in a vertical tube

An experimental study of heat transfer to boiling liquids under natural convective flow has been carried out in a single tube vertical thermosiphon reboiler to investigate the effect of heat flux and submergence on circulation rates. The test liquids used were distilled water, various concentrations of propan-2-ol in water and their azeotrope. The test section was an electrically heated stainless steel tube of 25.56 mm i.d., 28.85 mm o.d. and 1900 mm long with twenty-one spot welded copper constantan thermocouples to measure the variations in wall temperature along its axis. The uniform heat fluxes in the range of 3.5–42.4 kW/m² were employed while inlet liquid sub-cooling varied from 0.2 to 30.7 °C. The liquid submergence levels were maintained in the range 30–100%. The typical experimental data has been graphically presented and discussed. An empirical correlation has been developed from the experimental data of the present study through regression analysis.     

Natural convection from narrow horizontal plates at moderate Rayleigh numbers

The present work deals with the natural convection flow and heat transfer from a horizontal plate cooled from above. Experiments are carried out for rectangular plates having aspect ratios between φ=0.036 and 0.43 and Rayleigh numbers in the range 290?Ra_w?3.3×10⁵. These values of Ra_w and φ have been selected below those commonly considered in previous research in view of a future application to the design of printed circuit boards. The plates are made of two different metals, copper and steel. The choice of a metal is relevant to the present problem because the plates are heated by means of an electric current. Important variations of the surface temperature are observed along the transverse direction for the steel plates. The surface of the copper plates is almost isothermal because of the high thermal conductivity of the metal.Calculations for a semi-infinite plate are carried out to predict the transverse profiles of the surface temperature and heat flux and to visualize the structure of the flow. Three-dimensional calculations are also used at a qualitative level to observe the changes in the flow structure due to the finite length of the plate. Present results are compared with both previous experimental work and analyses that are based on boundary layer theory. It is shown that analyses for an infinite boundary layer are not completely applicable to the present problem because of its different physics. The most relevant feature of the natural convection flow, which is not predicted by boundary layer analyses, is a thermal plume rising near the center of the plate.Present heat transfer results differ from previous experimental work because of the lower Rayleigh numbers and aspect ratios investigated here. The Nusselt number is found to depend on Ra_wⁿ, with the exponent n=0.17 being lower than most of the values reported in the literature. This comparatively low value is related to the transverse conduction of heat through the air, which becomes increasingly significant as Ra_w approaches zero. It is shown that such a low-Ra_w effect can be accounted for in a physically consistent manner by adding a constant term to the heat transfer correlation. On the other hand, it is found that the Nusselt number does not significantly depend on the aspect ratio in the range of φ investigated contrary to what has been previously reported for wider plates.     

线缆护套材料在我国西部环境中的试验研究

本文通过对线缆外护套材料在我国西部地区严酷环境试验站中土壤和大气1～5年的试验结果分析，总结了塑料护套材料的耐蚀性能。为线缆护套的防护设计、合理选材及制定标准提供科学依据。     

AgNO<Subscript>3</Subscript> spray tests: advantages,weaknesses, and various applications to quantify chloride ingress into concrete. Part 1: Non-steady-state diffusion tests and exposure to natural conditions

Within the framework of the evaluation and the prediction of chloride-induced corrosion risks, simple and rapid AgNO₃ spray tests can be proposed for various issues. This paper forms the first part of a series. In this first part, the Maultzsch procedure (spraying of 0.1-N AgNO₃ solution + K₂CrO₄) as well as the procedure based on the use of a sole AgNO₃ solution have been investigated on a broad range of concretes. These procedures have also been compared to the Collepardi procedure (spraying of 0.1-N AgNO₃ + fluoresceine). The feasibility of these colorimetric techniques on saturated specimens cast in laboratory, after non-steady-state diffusion tests carried out in various conditions, is discussed. In addition, the results obtained from applying such spray tests in field conditions on cores drilled out from various RC test specimens exposed to a marine environment (tidal zone) and to a road and cold environment (freezing-thawing cycles and spraying of deicing salts) are presented. Colorimetric methods have in particular been applied here to the assessment of the average chloride penetration depth and of its evolution versus time (kinetics). Moreover, the detection threshold of these techniques has been investigated in various environments. The possible sources of discrepancy on the results have been analysed.     

基于自然地理形态的道路测设及其曲线方程的拟合

在山区村镇及风景旅游名胜区的建设中，其道路的曲线测设，往往要基于自然地理形态进行，也就是路径的选择，有时具有不可选择性，且要求与实地具有最大的符合性。因此，其测设的作业方法不同于一般意义的道路测设；其曲线方程的建立，也是极其困难的。本就基于自然地理形态的道路测设工作的曲线类型的选择、曲线的拟合方法、曲线方程的建立及其数据的计算，提出了利用CAD技术进行曲线拟合、曲线方程的建立、曲线计算的实用技术方法。     

A new ‘Tailor-made’ methodology for the mechanical behaviour analysis of rubber-like materials: II. Application to the hyperelastic behaviour characterization of a carbon-black filled natural rubber vulcanizate

The purpose of this paper is the modelling of the mechanical behaviour of an elastomeric material, through detailed experimental and numerical procedures, specific to large strains. The experimental technique is based on in-plane kinematics measurements using a speckle extensometer, from which the whole two-dimensional field of in-plane displacements is obtained by a digital image processing [Polymer (2002)]. This part of the work concerns the identification of the constitutive equation for a carbon black natural rubber (NR) vulcanizate. We start by quoting some theoretical considerations relative to rubber elasticity and stress-softening effect, which is the counterpart of the filler reinforcement. Then, we describe the experimental procedure and present data for both non-preconditioned and preconditioned samples. Next, the identification of the constitutive law parameters using a minimization algorithm is driven. Finally, we present the validation of the constitutive model, by its implementation into the finite element code SYSTUS and the numerical simulation of the response of a double edge notched tensile (DENT) specimen.     

Premixed metal fibre burners based on a Pd catalyst

As an alternative to previously developed catalytic FeCrAlloy fibre mat burners based on perovskite catalysts, new catalytic burners have been developed based on Pd catalyst on lantana-stabilised Al₂O₃ and different fibre structures (NIT100A, NIT100S and NIT200S by ACOTECH NV). All development steps are considered, shifting from catalyst preparation (based on combustion synthesis of γ-Al₂O₃) to the optimisation of lantana and Pd loadings, from the definitions of the best catalyst-deposition conditions (washcoating) to the catalytic burners performances, determined in an ad hoc developed combustion chamber. The results show almost half pollutants emissions and better performance compared to various non-catalytic counterparts, especially as far as CO and NO_x emissions are concerned. Some flame instability problems were though registered, especially for one of the catalytic burner mattresses employed, at low specific power inputs and excesses of air (<375 kW/m² and <12%, respectively). Further, PdO/Pd transition is shown to influence the dynamic behaviour of the catalytic burners.     

������Һ����CO2����ѧ

天然气脱除Ｈ２Ｓ和ＣＯ２是天然气净化领域经常遇到的问题。Ｈ２Ｓ与醇胺的反应属瞬间质子反应，ＣＯ２与醇胺的反应则复杂得多，醇胺溶液对Ｈ２Ｓ的选择性分离主要依靠ＣＯ２与醇胺的反应速度差异来实现。文章介绍了伯胺，仲胺，叔胺及空间位阻胺溶液反应的机理和动力学。