Nonlinear response in glass fibre non-crimp fabric reinforced vinylester composites

This paper addresses the nonlinear stress-strain response in glass fibre non-crimp fabric reinforced vinylester composite laminates subjected to in-plane tensile loading. The nonlinearity is shown to be a combination of brittle and plastic failure. It is argued that the shift from plastic to brittle behaviour in the vinylester is caused by the state of stress triaxiality caused by the interaction between fibre and vinylester. A model combining damage and plasticity is calibrated and evaluated using data from extensive experimental testing. The onset of damage is predicted using the Puck failure criterion, and the evolution of damage is calibrated from the observed softening in plies loaded in transverse tension. Shear loading beyond linear elastic response is observed to result in irreversible strains. A yield criterion is implemented for shear deformation. A strain hardening law is fitted to the stress-strain response observed in shear loaded plies. Experimental results from a selection of laminates with different layups are used to verify the numerical models. A complete set of model parameters for predicting elastic behaviour, strength and post failure softening is presented for glass fibre non-crimped fabric reinforced vinylester. The predicted behaviour from using these model parameters are shown to be in good agreement with experimental results.     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

Stress-strain relations in elastoplastic solids with Dugdale-type cracks

Mechanical behavior of a two-dimensional elastoplastic solid with rectilinear cracks is investigated. Plastic strip model is used to reduce plasticity problem to the equivalent linear elasticity formulation. Two realizations of the mixed mode plastic strip model are considered: in-line plastic strips as proposed by Becker and Gross [Int. J. Fract. 37 (1988) 163], and inclined plastic strips of Panasyuk and Savruk [Appl. Mech. Rev. 47 (1994) 151]. The effective mechanical response predictions are based on the procedure presented in Kachanov et al., [Appl. Mech. Rev. 47 (1994) 151]. Stress-strain relations are obtained for parallel and randomly oriented non-interacting cracks. Results are compared with known elastic solutions.     

The effect of doubly tapered strut morphology on the plastic yield surface of cellular materials

Although the literature on the mechanics of cellular materials is vast, there is no theoretical model to account for the effects of axial yielding of struts aligned to the applied loading direction on the plastic yield surface under multiaxial loading conditions. An anisotropic hexagonal model having tapered strut morphology is developed to show these effects on the plastic yield surface under multiaxial tensile loading condition. This model covers several types of cellular structure such as two-dimensional (2D) hexagonal and square cellular materials, and three-dimensional (3D) hexagonal and rhombic cellular materials of rod-like columnar structure. A tetrahedral element with tapered strut morphology is also used for a foam model to illustrate these effects on the yield surface under axisymmetric loading condition. Plastic collapse due to bending moment in the inclined struts is a dominant mode. However, under multiaxial tensile loading, the collapse due to axial yielding of struts parallel to the loading direction is found to be an important mode. The shape of plastic yield surface was found to depend not only on relative density but also on the strut morphology.     

软β核素内部样品塑料闪烁探测器

本文评价了塑料闪烁片用作软β核素探测器时的计数效率、β谱、本底谱和康普顿电子谱的特征。文中强调:采用胶合光导剂构成的系统是一种新型探测器(软β核素内部样品塑料闪烁探测器)。本文提出内部样品固体探测器、胶合光导剂和胶合闪烁光导剂的新概念。     

Theory of propagating deformation bands

A model for propagating deformation bands is developed, based on a mechanical equation of state and on evolution equations for the structure parameters. It is shown that, contrary to normal deformation, it is necessary to discriminate between global parameters which depend solely on time elapsed and local parameters which are functions of the strain history. Correspondingly, two sets of equations are presented, one describing the development of the global parameters in the course of time, the other giving the evolution of the local state parameters in the course of deformation, i.e. as a function of strain. Measurable quantities derived from the first set are the load serrations and the band velocity, while the second set yields the flow stress and the strain profile of the propagating band.     

塑料用抗静电剂

简要介绍了塑料抗静电剂的特性、抗静电机理、使用方法、影响因素和效果评价。概述了抗静电剂的国内现状和发展趋势。     

影响塑料模压制件内应力的因素分析

主要讨论了造成塑料模压制件内应力的主要因素,包括制件造型设计不合理、模具设计不合理、成型工艺条件不正确等,并针对不同情况给出了相应的解决办法     

Energy absorption in splitting square metal tubes

This paper presents an investigation into the energy absorbing behaviour of axially splitting square metal tubes. Tubes 50 mm square with a variable thickness were pushed slowly against rigid pyramid shaped dies, which had various semi-angles. By pre-cutting 5 mm long slits at the four corners, the tube splits along the corners and curls outward with a certain radius at a constant force. In this energy dissipating system, there are three components: tearing energy, plastic deformation energy and frictional energy. Theoretical analysis of the three energy components is presented. Curl radius is also studied in detail. Good agreement between experiments and theory is obtained. The results show that tubes which both split and curl may be used as efficient, long stroke energy absorbing devices.     

Charge transfer resistance of spray deposited and compressed counter electrodes for dye-sensitized nanoparticle solar cells on plastic substrates

Electrochemical impedance spectroscopy was used to determine the effective charge transfer resistances of porous dye-sensitized solar cell counter electrodes prepared by low-temperature spray deposition and compression of conductive carbon and platinized Sb-doped SnO₂ powders on indium tin oxide-coated plastic substrates. The charge transfer resistances were 0.5–2 and 8–13 Ω cm², respectively, when using 3-methoxypropionitrile as the electrolyte solvent. The manufacturing method used lends itself to produce mechanically stable and even-quality electrodes in an easy and fast manner.