影响塑料模压制件内应力的因素分析

主要讨论了造成塑料模压制件内应力的主要因素,包括制件造型设计不合理、模具设计不合理、成型工艺条件不正确等,并针对不同情况给出了相应的解决办法     

封隔器胶筒接触应力分布有限元计算

利用ANSYS软件对3种封隔器胶筒的接触应力进行了有限元计算，得到了接触应力沿胶筒轴向的分布情况。比较不同结构封隔器胶筒在相同条件下的接触应力分布，可知新型封隔器胶筒在高压下接触应力分布更为均匀合理，具有较好的应用前景。     

超薄氧化层中的中性陷阱对隧穿电流的影响和应变诱导漏电流

用数值分析的方法讨论了中性陷阱对超薄场效应晶体管(MOSFET )隧穿电流的影响.中性陷阱引起势垒的变化在二氧化硅的导带中形成一个方形的势阱.对于不同的势垒变化,计算了电子隧穿氧化层厚度为4nm的超薄金属氧化物半导体结构的电流.结果表明,中性陷阱对隧穿电流的影响不能被忽略,中性陷阱的存在使隧穿电流增加,并且通过这个简单的模型能够理解应变诱导漏电流的产生机制.     

推进波作用下的底泥起动

在介绍推进波作用下底泥起动特点的基础上，将上层水体作为粘性流体，底泥作为粘弹性体，推导了推进波作用下泥床面剪应力的表达式，并根据试验结果，给出了推进波作用下底泥起动时的床面剪应力与底泥流变参数的关系。     

Residual stress measurements in bevel gear after different production phases

This article discusses residual stress measurements by means of electrochemical removal of material layers with residual stresses and simultaneous measurement of strain on the opposite specimen side with strain gages. Exact measurements are impossible particularly because of the small bevel gear module. With the method presented, the average residual stresses in the tooth root plane and underlying layers are measured. Residual stress distribution after each consecutive production phase is plotted and analyzed. Residual stress measurements enable the engineer to adequately assess each individual production phase and by that improve the quality of the complete production process.     

Non-destructive evaluation of residual stresses in thin films via x-ray diffraction topography methods

Quantitative x-ray diffraction topography techniques have been used to measure the residual strain magnitude and uniformity of deposition for Mo and W sputtered films on Si(100) substrates. High sensitivity rocking curve measurements were able to determine differential strains for films as thin as 2.5 nm; while Bragg angle contour mapping had similar sensitivity and was also able to assess coating uniformity and stress distribution over areas covering a whole wafer. Measurements of strain versus film thickness over a range of 2.5 nm to 80 nm showed that a critical thickness exists for maximum residual strain. Growth beyond this range produces stress relaxation. This non-destructive type of analysis could be employed on a wide range of film-substrate combinations.     

Effect of heating-rate on failure temperature of pre-loaded brass H62

The response and failure of brass H62 specimens subjected to different levels of pre-loaded stresses and heating rates were investigated using a Gleeble-1500 thermal-mechanical material testing system. The metallographs of the tested material were also observed and analyzed. It is found that the increase of either pre-loaded stress or heating-rate decreases the failure temperature. Metallographic analysis shows that high heating-rate may cause stronger local thermal inconsistency （LTI） and remarkably increase the microdefects in the material, which may markedly degrade the macroscopic mechanical properties of the material.     

发育有切割井眼结构面的井壁稳定性评价研究

切割井眼结构面的存在弱化了井壁的稳定性，常规完整井眼的井壁稳定分析理论已不能完全适用于受结构面切割的井眼。基于摩尔-库仑理论，在分析结构面应力状态的基础上，给出了井眼受结构面切割的井壁稳定性评价方法，并研究分析了结构面产状对井壁失稳的影响。结果表明，井壁的稳定性与原地应力状态、结构面产状以及结构面的力学性质有关，在其它因素一定的情况下，结构面的走向与倾角对井壁的稳定与失稳方位有着较大的影响。因此，准确评价结构面产出状态是提高井壁稳定性评价精度的前提。     

内燃机车曲轴中频淬火过程的数值模拟

借助 ANSYS大型有限元分析软件 ,实现了 16 V2 4 0曲轴淬火过程的计算机模拟 ,模拟结果可直观地显示出任一时刻曲轴表面及内部的温度分布、冷却曲线以及淬火结束后的残余应力分布 ,并能预测淬硬层深度。同时对比了轴颈内圆角处进行淬火和不进行淬火两种工艺的效果 ,为现场提供了用虚拟现实方法详尽分析和研究淬火工艺的工具。