磷对Ni3Al凝固组织的影响

磷(P)在Ni3Al中的溶解度很低，凝固过程中向剩余液体中偏聚，最终在晶界上析出富P相，凝固后期。P在剩余液体中的偏聚程度升高，降低形核率，抑制试样心部等轴晶的形成，促使试样外缘晶粒向心部延伸生长，增加柱状晶长度。P降低合金终凝温度，增如糊状区长度，阻碍液相补缩，增加形成疏松的倾向。P产生上述作用的根本原因是其降低固、液两相体积自由能差和原子跃迁穿过液／固界面的激活能。     

STUDY ON Ni-Cr SYSTEM SOLAR SELECTIVE THIN FILMS PREPARED BY MAGNETRON REACTIVE SPUTTERING PROCESS

1. IntroductionSolar selective thiIl solid fil1us are the key part for solar heat collect'ors. But ll1ostfactories still produced solar absorptive filn1s by traditional tecIl11ology sucl1 as pai1ltillga1ld electrocl1eluical process that nlust result in po…     

低碳钢中磷的偏聚与再结晶织构

本文用正、倒极图和ODF法研究了低碳钢板在不同冷轧和再结晶退火条件下,磷对再结晶织构的影响。用金相术、扫描电镜和电子探针研究了磷在钢中的分布和显微组织。结果发现,磷促进了与轧向平行的一组〈001〉和与轧面法向平行的一组〈111〉纤维织构的生成;这种作用与预退火温度密切相关,在390和590℃进行预退火就呈现,在490℃就抑制。在促进织构生成的预退火温度时产生晶内磷偏聚的异常显微组织。并认为这种纤维织构的形成与晶内磷偏聚有关。     

ZrB2-SiC基超高温陶瓷（UHTCs）的反应烧结及SHS粉体制备

用普通反应热压方法（RHP）和反应放电等离子体方法（R-SPS）原位反应制备了ZrB2-SiC，ZrB2-SiC—ZrC，ZrB2-SiC-ZrN，以及ZrB2-SiC-AIN4种复合材料。从密度，物相以及显微结构等方面比较了两种烧结方式之间的差别，对于升温速度较慢的普通热压方法，反应分步进行，显微结构不均匀；对于升温速度快的放电等离子体烧结，原料间的自蔓延反应被点着，反应速度快，显微结构均匀。同时以红外灯的热量为点火源，引发了Zr，Si及B4C间在空气气氛下的自蔓延反应，制备了较纯及粒径约为1μm的活性粉体。     

高温W/Re流口复合界面上的扩散层

W/Re流口在高温下使用时,复合界面处会发生反应扩散而形成一个由固溶体(W),双相σ,双相x,固溶体(Re)4个相组成的过渡层。并作出了不同反应扩散时间的浓度分布曲线,及浓度突变形成的双相区,从而确定了各相成份组成。对经反应扩散后的复合界面进行微观观察发现x相、σ相内有许多间隔式微裂纹,据此认为高温下W/Re流口失效原因是使用过程中上述两x,σ相内裂纹扩散,熔体渗入所致。     

Effects of phosphorus addition on the magnetic properties of sintered Fe-50 wt.% Ni alloys

Phosphorus was added to Fe-50 wt.% Ni in the form of a coated composite powder via an electroless plating process. Addition of phosphorus to Fe-50 wt.% Ni facilitated increases in density and grain size, both of which were beneficial to magnetic performance. Because of the homogeneous distribution of phosphorus in the powder, the optimal phosphorus addition was much lower than for those using Fe₃P as the phosphorus precursor. The optimal phosphorus addition was close to its maximum solubility in Fe-50 wt.% Ni (about 0.5 wt.%), above which precipitation of excessive phosphorus in the form of iron nickel phosphide, (Fe,Ni)₃P, effectively degraded the magnetic properties of Fe-50 wt.% Ni. Without the addition of phosphorus, good magnetic properties could be achieved only when the sintering temperature was high enough (>1200 °C) to result in a high sintered density and large grains in the sintered structure.     

环保型反应性乳化剂在水性木器乳液聚合中的应用

介绍了环保型反应性乳化剂ADEKA?REASOAP?SR-10、ER-30的结构和特性,重点分析了反应性乳化剂在水性木器乳液聚合中的应用及其对聚合物性能的影响。实验证明,应用反应性乳化剂所得的聚合物性能要远远优于非反应性乳化剂所得聚合物性能,而且应用了非离子反应性乳化剂所得的聚合物性能要优于单独使用阴离子反应性乳化剂所得聚合物性能。最后预测了环保型反应性乳化剂的良好应用前景。     

Fertilizers and eutrophication in southwestern Australia: Setting the scene

An excess of plant nutrients has caused serious eutrophication in aquatic ecosystems of southwestern Australia manifested by excessive growth and accumulation of green and bluegreen algae. Phosphorus is generally the limiting nutrient for algal growth and phosphatic fertilizers applied to nutrient-deficient, leaching, sandy soils are the main source of P, supplemented by rural industry point sources. Nitrogen is the limiting nutrient in marine embayments with little drainage from the land. Measures to reduce the load of P delivered to drainage include basing fertilizer application rates on soil testing for P and the use of less soluble P fertilizers. Catchment management plans are being implemented with community involvement to reduce P loads and maintain agricultural production. This introductory paper reviews the history of eutrophication in southwestern Australia and of studies into its causes, principally in the large Peel-Harvey estuary. It briefly summarises other papers in this special issue concerned with different aspects of the problem: how to fertilize the land without causing eutrophication.     

新型颗粒状活性染料

本文阐述了颗粒状活性染料的制造特点、制造技术和品质评价，并列举了典型的商品。     

OP-1O丙烯酸酯的合成及其乳化特性的研究

本文对OP－10丙烯酸酯非离子反应性乳化剂的合成方法进行了研究，并对合成乳化剂的各种乳化剂性能进行了测试。经过测试和聚合实验表明，在本实验条件下，OP－10与丙烯酸可以有效地进行酯化反应，合成的OP－10丙烯酸酯有较好的聚合与乳化特性。