Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

Finite element simulation of the mechanics of flat contact pad fretting fatigue tests

An understanding into the macro kinetic and kinematic behaviour of fretted surfaces is provided. Making use of a modified version of a previously developed in‐house two‐dimensional elastic–plastic finite element analysis numerically simulates flat contact pad fretting fatigue tests. Basic macro mechanics concepts are adopted to idealise two bodies with rough contact surfaces and loaded at two different sites with arbitrary axial loading profiles. A time scale factor is devised to recognise the earliest candidate out of the events possibly accommodated at each loading increment. The present analysis utilises a relevant experimental set up developed in the Structural Integrity Research Institute of the University of Sheffield as an application. Computational results accurate to within 1.2% and corresponding to one contact pad span and six constant normal loads acting individually with four amplitudes of two sinusoidal axial load cycles are presented. The present computations include (1) the development of the global and local normal and tangential reactions and relative sliding displacement acting along the fretting surfaces and (2) contact pad deformation, generated stress fields and plasticity development within the neighbouring region of the fretted area.     

Electron spectroscopies and their use for materials characterization

We present here a general overview of electron spectroscopies from a practical point of view. The most frequently used ones are described and the type of structural information they can provide on materials is explained in relation to the physical processes on which they are based. Furthermore, we explore critically and in detail various tools that have been developed to allow a systematic solving of structures by these spectroscopies.     

谈谈职业教育的大众性

对职业教育的大众性问题进行了论述、实证分析和理论、政策、改革等思考。     

Bruchanalyse an Hohlgläsern

Failure analysis of hollow glasses The failure analysis is very important to clarify damages of hollow glasses. Damages of glass bottle through over pressure are very often linked with damages to persons. This is the reason why the causal research is from particular importance. Different surface characteristics of glass fragments as well as the fracture pattern give hints to the direction of the crack, the stress just before breakage and the reason of stress. A reconstruction of the bottle is a further helpful instrument for cause studies. The difference of the various characteristics of the surface will be explained. Further on there will be discussed different reasons and mechanism of fracture.     

Determination of the total concentration and speciation of Al(III) in tea infusions

The aluminium species in different tea infusions were investigated, by determining their stability constants and concentration. This was done for some particular samples using a simple experimental method based on the sorption of aluminium on the strongly sorbing resin Chelex 100, by a batch procedure. From the thermodynamic information obtained it is possible to calculate the concentration of the different species, and in particular that of the free metal ion, which is very important for evaluating the adsorption of aluminium on biological membranes. It was found that aluminium in the tea infusions here considered is present at high total concentration, approximately 0.1 mM, but mainly linked to strong complexes, for instance with side reaction coefficient higher than 10(5.11) at pH 3.95 in one case (tea 1). This could be the reason for the low toxicity of aluminium in tea. These strong complexes were not dissociated even in the presence of Chelex 100. In this case only a limiting value of the reaction coefficient could be evaluated. The presence of the very strong complexes was found in all the tea sample here considered. In two of the considered samples (one black and one green tea) a part of Al(III) was linked to less strong complexes, for example with a reaction coefficient 10(4.14) (tea 2, pH 4.20). The presence in the considered tea infusions of other substances able to complex aluminium was also detected, by the well known ligand titration procedure, at concentration ranging from 0.65 to 3.37 mM in three tea infusions, and at somewhat higher concentration in the case of the ready drink, which was also considered for comparison.     

Barriers to Increased Engineering Graduate Enrollments: Counterforces and Their Implementation

This paper highlights the role of the faculty member in recruiting students currently enrolled in B.S. programs in engineering and the sciences into full-time pursuit of a graduate-level engineering degree. The faculty member is demonstrated to be in a unique position to influence such students, providing strong counterforces to a confluence of attitudes and pressures experienced during the B.S. experience which effectively create a barrier to full-time engineering graduate study. We analyze this barrier via the method of force field analysis, and demonstrate that effective recruitment into full-time graduate study must be based on a four-fold strategy of education, expectations, improved B.S. experience and better control of the B.S. environment. Approaches to implement these strategies are discussed.     

利用计算机进行油气资源评价和勘探决策

本文着重介绍了构成《现代勘探决策理论系统》的5个主要计算机模块,即:生油岩热演化处理、求任意曲边形面积、数学模拟预测资源量、勘探经济评价分析及决策、辅助处理等模块。该系统曾在塔里木盆地和准噶尔盆地的油气资源评价和勘探决策中发挥了作用,受到了专家和用户的好评。     

Influence of Two Salicylate Components on the Particle Size of an Oil-in-Water Emulsion with Nonionic Surfactants

This paper reports a study undertaken using techniques of static and dynamic light scattering to investigate the influence of sodium salicylate and methyl salicylate on droplet size of oil-in-water emulsions. The rates of changes were measured by determining the size and distribution of the oil droplet in the material. All emulsions showed a bimodal size distribution; the mean diameters and polydispersity were calculated from intensity. These data were analyzed with nonlinear regressions and bootstrap methodology. An amount of methyl salicylate component induced a decrease of mean diameter and standard deviation. On the contrary, sodium salicylate entailed the growth of all droplet populations and coalescence for the highest concentration.     

Theoretical and experimental evaluation of the limit state of transit gas pipelines having corrosion defects

The limit carrying capacity of gas pipelines having corrosion defects were evaluated by means of an improved FEM analysis, together with the ANSI/ASME defect judgement and an experimental verification. When compared with our past presentation at the proceedings of the CAPE'93 Colloquium (dealing with reproduced defects), this paper evaluates the remaining lifetime of a pipeline having natural faults. The new improved analysis includes geometrical nonlinearities leading to a modification of limit state parameters and thus matching better with actuality. This presented work was initiated by the firm of Trans-Gas in Prague after having had a pipeline inspected proving some parts of it as being heavily corroded. The task in hand was to determine the remaining pipeline lifetime with the view to at least a two-year period.