挤压变形对Mg95Zn4.3Y0.7合金组织和性能的影响

研究了在250℃、不同挤压比下挤压变形对Mg95 Zn4.3 Y0.7合金组织及性能的影响。结果表明，Mg95 Zn4.3 Y0.7经过挤压变形后，合金中晶界处的共晶相破碎，弥散分布至晶粒内部，并且晶粒显著细化。同时，随着挤压比的增大，晶粒细化程度增加，合金的力学性能单调增加。当挤压比为16时，合金晶粒尺寸为5-8μm，抗拉强度为288.9MPa，显微硬度HV值为117.8。     

国内轴承钢的生产现状及发展

介绍了2002年国内高碳铬轴承钢的产量及品种结构，评述了国内轴承钢生产工艺装备、质量状况和发展方向。     

滑轨升降拉钢台架的结构、强度、钢度分析

介绍了攀钢轨梁厂钢轨收集装置——滑轨升降式拉钢台架的结构,并计算了主要受力构件滑轨的强度和刚度。     

超低硫X65管线钢中非金属夹杂物研究

对本钢超低硫X65管线钢中夹杂物的研究结果表明,LF精炼初期,钢中夹杂物主要是球形、多边形和大量簇状的Al2O3夹杂物,99.1%的夹杂物尺寸小于20μm。微合金化后,部分Al2O3夹杂物中出现TiO、SiO2、MnS等成分。钙处理后,夹杂物的平均直径达到8.58μm,大量夹杂物为含有微量MgO、SiO2或MnS等的2~50μm的球形mCaO.nAl2O3,部分为Al2O3、MnS、CaS或CaS-MnS。铸坯中夹杂物数量最少且尺寸最小,96.9%的夹杂物尺寸小于10μm,未发现大于50μm的夹杂物,平均直径为3.71μm。铸坯中大部分为球形的以mCaO.nAl2O3为主要成分的复合夹杂物,还有少量的Al2O3、MnS和CaS夹杂物等。     

支持向量机及其在径流预测中的应用

给出了支持向量机方法(SVM)的思路、特点及关键之处,探讨了SVM在径流预测中的可能性,并与基于遗传算法的门限回归模型(TR) 进行了对比分析。径流预测实例分析表明,在拟合阶段,SVM模型要好于TR模型;在预留检验阶段,SVM模型与TR模型接近。同时SVM模型适合于小样本情况且能达到全局最优。SVM模型用于径流预测是可行的、优越的。     

Exploring the methods on improving CH4 delivery performance to surpass the Advanced Research Project Ageney-Energy target

CH_4 storage associated with adsorbed natural gas(ANG) technology is an issue attracting great concern.Following the Advanced Research Project Agency-Energy(ARPA-E) targeted deliverable capacity of 315 cm~3·cm~(-3)(STP), hundreds of thousands of materials have been experimentally or theoretically evaluated,while the best results still show a 35% gap from the target. Moreover, recent theoretical research reveals that the target is beyond the possibility that real materials can be designed. To get rid of the awkward situation, we make attempts on investigating the CH_4 delivery performance under other operation conditions. Methods of raising the discharge temperature(to infinite high) or elevating the storage pressure(to 25 MPa) have been proved to show limited effectiveness. In this work, it is found that the ARPA-E target can be achieved by using a decreasing storage temperature strategy. By taking 280 Co RE(computation-ready, experimental) COFs(covalent organic frameworks) as ANG materials, when reduce the storage temperature to 190.6 K, the highest deliverable capacity can reach 392 cm~3·cm~(-3)(STP), and16.1% Co RE COFs can surpass the target. The target is also achievable when storage at 220 K. Structure performance relationships study shows strong correlation between deliverable capacity and void fraction. Hence, 120 hypothetical COFs are generated to ascertain the optimum void fraction. In addition,the performance of 2 D-COFs can be greatly enhanced by increasing the interlayer spacings, e.g. CH_4 deliverable capacity(storage at 190.6 K) of ATFG-COF can be improved from 239 to 411 cm~3·cm~(-3)(STP) when interlayer spacing is enlarged to 1.65 nm.     

混合材对水泥浆体泌水性能的研究

通过调整水泥中钢渣粉、粉煤灰和石灰石粉的含量,检测水泥浆体泌水速率,研究了多种混合材对水泥的泌水性能的影响,结果表明：建立的水泥浆体泌水检测方法可以表征水泥的泌水性能;5%～6%的钢渣粉的加入促进了水泥整体的保水效果,泌水速率和累积泌水率较现行水泥配比和中联水泥的低,但水泥成本上升 2.13元/t和2.89元/t;粉煤灰因其密度低,且多为球状形貌,不利于水泥泌水性能;2%石灰石粉的加入,可降低水泥的泌水率和累积泌水率,其性能曲线与中联水泥的相近,水泥成本降低0.96元/t。     

Preparation of ceramic coatings on inner surface of steel tubes using a combined technique of hot-dipping and plasma electrolytic oxidation

A new method for inner surface modification of steel tubes, named a combined technique of hot-dipping and plasma electrolytic oxidation (PEO) was proposed and demonstrated in this paper. In this work, metallurgically bonded ceramic coatings on inner surface of steel tubes were obtained using this method. In the combined process, aluminum coatings on steel were firstly prepared by the hot-dip process and then metallurgically bonded ceramic coatings were obtained on the aluminum coatings by PEO. The element distribution, phase composition and morphology of the aluminide layer and the ceramic coatings were characterized by SEM/EDX and XRD. The corrosion resistance of the ceramic coatings were also studied. The results show that, after hot-dip treatment, the coating layers consist of two layers, where Al, Fe_xAl _(1−x) were detected from external topcoat to the aluminide/steel substrate. Then after PEO process, uniform Al₂O₃ ceramic coatings have been deposited on inner surface of steel tubes. The ceramic coatings are mainly composed of -Al₂O₃ and γ-Al₂O₃ phase. The compound coatings show favorable corrosion resistance property. The investigations indicate that the combination of hot-dipping and plasma electrolytic oxidation proves a promising technique for inner surface modification of steel tubes for protective purposes.     

从改革中求发展 从改革中求效益

总结了解放４５年来上海钢铁工业所取得的成就，重点阐述了技术、工艺、装备方面的现状和不足以及发展目标，指出：只有实行改革开放，加快技术改造，才能提高上海钢铁工业的总体水平，提高经济效益，也才能使老企业焕发青春，步入现代化钢铁工业之林。     

圆坯连铸GCr15SiMn的成分偏析和接触疲劳寿命研究

利用金属原位分析技术和钻孔化学分析方法对高淬透性轴承钢GCr15SiMn的Φ450 mm连铸圆坯和Φ130 mm圆钢的C、Si、Mn、Cr元素横截面的分布情况进行分析。采用推力片式接触疲劳试验机进行了材料的接触疲劳寿命测试。结果表明：GCr15SiMn连铸圆坯C元素的偏析倾向较大,易产生中心正偏析,而Cr、Si、Mn元素的偏析倾向较小。通过采取稳定低过热度浇铸、三段强电磁搅拌等措施,铸坯的中心碳偏析得以改善。采用(1240±20)℃×5 h高温扩散、初轧首道次变形量≥90 mm大变形轧制的Φ130 mm圆钢的碳偏析可以得到进一步的改善,试验钢在5.3GPa高应力负载下的接触疲劳额定寿命L₁₀达到3.58×10⁶次,接近电渣重熔钢的水平。