军用滑木箱的设计分析

介绍了按日本标准设计的横板式和国内竖板式军用滑木箱的结构设计参数，从木箱抗弯、抗静压及顶盖抗弯三方面对比了两种木箱的力学性能，分析了两种木箱的特点及适用范围。     

Cr12钢的预处理工艺研究

本文研究了Ｃｒ１２钢经４种不同的预处理工艺处理后钢中碳化物的大小，数量，分布及钢的硬度，强度和韧性，试验结果表明，经调质处理，高温固溶淬火＋高温退火处理后，Ｃｒ１２钢中碳化物的大小，分布及其组织，性能均优于常规球化退火预处理的。通过扫描电镜对冲击断口的分析，初步探讨了新的预处理工艺提高韧性的原因。     

Effect of cationic surfactant and inorganic anions on the electrochemical behavior of carbon steel in formation water

Corrosion behavior of carbon steel in formation water associated crude oil from Egyptian western desert was studied at various concentrations of dodecyl dimethyl ammonium chloride (CS) as a cationic surfactant. Polarization curves indicate that CS has a good inhibition efficiency for carbon steel in formation water and behaves as cathodic inhibitor. The inhibition efficiency was found to increase with increase in CS concentration until reaches a maximum constant value corresponding to the critical micelle concentration of CS and decrease with increase in solution temperature. The adsorption of CS follows the kinetic thermodynamic model and Flory-Huggins isotherm. Thermodynamic parameters obtained indicate that that the presence of the CS increases the activation energy. Polarization and Impedance measurements indicate that the addition of KI has a significant synergistic effect with CS and results in increase the inhibition efficiency of CS in formation water.     

高频超声波在氧化皮中传播性能标定

对高频超声小在12Cr2MoWVTiB(G102钢）和12Cr1MoV钢钢管运行所产生氧化皮中的传播速度进行了定量标定，并对标定误差进行了统计计算，结果表明，12Cr1MoV钢氧化皮测厚标定点最大偶然误差值为0．050mm,G102钢为0．030mm，并指明了误差来源。     

工业建筑中钢结构的设计

钢结构已广泛应用于工业建筑中 ,本文叙述了工业建筑中钢结构的设计     

低温聚合物结构松弛的数值研究

为了获得低温聚合物的参数和升降温速率对连续升降温无量纲比热容的影响,应用差示扫描量热法(DSC)和TNM的结构松弛模型作出简单的数值研究.结果表明,变换不同比率的升降温速率及不同参数值得到的DSC曲线图形变化能够对聚合物的结构松弛研究有一点参考作用.     

Investigation of structural properties of ITO thin films deposited on different substrates

The influence of the substrate nature on the structure and morphology of ITO thin films grown by thermal evaporation in vacuum is investigated. The as-prepared metal films with Sn/In molar ratio of 0.1 were subsequently annealed for 2 h at 723 K in air (to obtain tin doped indium oxide), then annealed in vacuum at 523 K, followed by UV irradiation (to reduce the electrical resistivity). Irrespective of substrate nature, XRD data evidence a (222) preferential orientation in films. Substrate nature, annealing in vacuum and UV irradiation influence the structure, morphology, optical, electrical and surface wetting properties of the films' surface.     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

Correlation between quasi-static and dynamic crack resistance curves

The correlation between the crack resistance measured from dynamic and quasi-static J-R tests has been investigated based on test data from instrumented Charpy impact tests and quasi-static single edge notched bend (SENB) J-R tests.The method originally proposed by Aurich et al. [Analyse und Weiterentwicklung Bruchmechanischer versagenskonzepte--Lokales Risswachstum, Ermittlung des Risswiderstandsverhaltens aus der Kerbslagarbeit. BAM Forschungsbericht 192, Berlin 1993, ISBN 3-89429-329-2], to develop a correlation coefficient between the net fracture resistance of Charpy V-notch (ISO) and quasi-static compact tension tests, was extended to establish correlations between so-called ductile-brittle transition fracture resistance curves obtained from instrumented Charpy V-notched (ISO) and fatigue precracked impact tests and quasi-static SENB J-R fracture resistance tests.The correlation between the dynamic and quasi-static crack resistance with regard to practical application to fracture assessments appears to be reasonably consistent, bearing in mind the inherent scatter in crack resistance data in general. The findings of the present research project from testing of ship grade NVE 36 and pressure vessel steel to ASTM A516 Gr. 70 as well as two weldments in the NVE 36 steel, are in excellent agreement with the results of the research conducted by Aurich et al. [Analyse und Weiterentwicklung Bruchmechanischer versagenskonzepte--Lokales Risswachstum, Ermittlung des Risswiderstandsverhaltens aus der Kerbslagarbeit. BAM Forschungsbericht 192, Berlin 1993, ISBN 3-89429-329-2] for structural and pressure vessel steels to the German DIN standard steels including St 52-3, StE 355 and StE 460.     

平板钢闸门止水问题的探讨

本文介绍了平板钢闸门各部位的止水结构型式，并要求设计合理，制造、安装要保证精度，才能保证止水效果良好。