Conceptual damage-sensitive features for structural health monitoring: Laboratory and field demonstrations

The use of damage-sensitive features to evaluate structural condition or health is a very critical aspect of structural health monitoring. The purpose of this paper is to investigate the potential of two different damage-sensitive features for detecting damage. Different damage scenarios are simulated on a large-scale laboratory structure and a three-span highway bridge for demonstration. The features presented in this paper are the modal flexibility-based deflection and curvature both of which are obtained directly from dynamic properties. In the literature, flexibility associated with mode shapes and mode shapes curvatures have been mostly explored. In this study, multi-input–multi-output dynamic data are used to obtain modal flexibility, which is a close approximation to the actual flexibility. A main novelty is that the curvature is calculated from the deflected shapes using the modal flexibility as opposed to using modal vectors. In this paper, the theory of the methodology is explained and then experimental studies and results are presented. For the experimental studies, the laboratory specimen and the three-span bridge were gradually damaged. It is shown that both deflection and curvature are conceptual and physically meaningful features for damage detection and localization. The issues and the requirements for these features to perform successfully are also presented.     

Growth of β-FeSi2 layers deposited from a molten salt

β-FeSi₂ layers have been successfully grown using a molten salt method for the first time. It was found that single phase and homogeneous β-FeSi₂ layers with a columnar domain structure can be grown on FeSi substrates. The layer thickness was demonstrated to be controllable by the growth temperature and time, and was diffusion controlled. It was shown that the layers were void- and crack-free compared to similar layers grown on Fe substrates: this difference is explained in terms of Fe diffusion. This vacuum-free simple growth technique is useful for the fabrication of large area semiconductor devices at low cost.     

Structural Appraisal of the Florentine Gothic Construction System

The nave of Santa Maria Novella, a Dominican church in Florence Italy is representative of a Florentine Gothic system of construction. This system, consisting of domical rib vaults on square nave bays, high side aisles, and crypto-buttressing, differs substantially from the French high Gothic system of even-level-crown rib vaults on rectangular bays, with flying buttresses over relatively low aisles. An investigation into the structural aspects of the Florentine Gothic construction system reveals that the domical vaults increase the longitudinal thrust and reduce the transverse thrust, which may require additional precautions to be taken during construction, but entails a less elaborate buttressing system. The domical vaults are found to perform well structurally, with an absence of tensile stresses, and are more suitable for a square bay. In general, the structural system of the nave of Santa Maria Novella is found to be the product of carefully considered structural design, which may be accepted as an alternative to the French Gothic construction system.     

Reliability Analysis of Single-Degree-of-Freedom Elastoplastic Systems. II: Suboptimal Excitations

A method for constructing an approximation of the critical excitation that drives an elastoplastic system from rest to a target threshold at a specified time instant, referred to as the “suboptimal excitation,” is presented in this paper. It is based on the observations gained from study of the critical excitations in the companion paper. Essentially, for the usual case of interest where the failure time is not small compared to the natural period, the duration of the positive and negative pulses of the critical excitation are roughly equal to half of the natural period. This consideration allows for a simple intuitive approximation of the critical excitation. The amplitudes of the positive and negative pulses are obtained in closed forms using energy balance. Numerical investigations show that the critical excitations are well approximated by the suboptimal excitations.     

Tedesko’s Philadelphia Skating Club: Refinement of an Idea

This paper presents new aspects of Anton Tedesko’s design for an important thin shell concrete roof. The study of this roof results from the examination of original engineering drawings and calculations which we present with the goal of promoting a greater understanding of the structural design of a major figure in the tradition of 20th century building.     

Structural Response of Nuclear Containment Shield Buildings with Construction Openings

Steam generator replacement at nuclear power plants requires large construction openings in nuclear containment structures. This study examines the effects of such openings placed in a 61?cm (2?ft) thick dome of a shield building. The dome is cast in two layers, and the limiting cases of the two layers acting as one and the lower layer carrying the entire load are considered. Without openings, the stresses due to dead load in the structure are very low when compared to the material strength. With openings, the loads are easily redistributed around the opening, and the maximum stresses for the conservative case are between three and four and one-half times larger than in the original structure with no openings. The extent of the affected area around the holes is relatively small. Smooth corners in the openings are necessary to avoid high local stress concentrations.     

Approach for Overcoming Numerical Inaccuracy Caused by Load Discontinuity

It was found that the discontinuity at the end of an impulse will lead to numerical inaccuracy as this discontinuity will result in an extra impulse and thus an extra displacement in the time history analysis. In addition, this extra impulse is proportional to the discontinuity value at the end of the impulse and the size of integration time step. To overcome this difficulty, an effective approach is proposed to reduce the extra impulse and hence the extra displacement. In fact, the novel approach proposed in this paper is to perform a single small time step immediately upon the termination of applied impulse, whereas other time steps can be conducted by using the step size determined from accuracy consideration in period. The feasibility of this approach is analytically explored. Further, analytical results are confirmed by numerical examples. Numerical studies also show that this approach can be applied to other step-by-step integration methods. It seems that to slightly complicate the programming of dynamic analysis codes is the only disadvantage of this approach.     

A damage identification technique for CF/EP composite laminates using distributed piezoelectric transducers

In this study, a damage identification approach was developed for carbon fibre/epoxy composite laminates with localized internal delamination. Propagation of the Lamb wave in laminates and its interaction with the delamination were examined. The fundamental symmetric Lamb wave mode, S₀, and the lowest order shear wave mode, S₀^′, were chosen to predict damage location. A real-time active diagnosis system was therefore established. This technique uses distributed piezoelectric transducers to generate and monitor the ultrasonic Lamb wave with narrowband frequency. The two-way switches were employed to minimize the number of transducers. A signal-processing scheme based on the time–frequency spectrographic analysis was utilised to extract useful diagnostic information. Also, an optimal identification method was applied on damage searching procedure to reduce errors and obtain the diagnostic results promptly. Experiments were conducted on [0/−45/45/90]_s CF/EP laminates to verify this diagnosis system. The results obtained show that satisfactory detection accuracy could be achieved.