Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

Mechanical behaviour of a combined joint composed of mechanical fastening and adhesive bonding

A study has been made of ‘combined’ joints consisting of mechanical fastening and adhesive bonding between rigid adherends. The mechanical characteristics of such ‘hybrid’ butt and lap shear joints have been derived by theoretical analysis. Results from experimental tests in combined joints giver reasonable agreement with the theoretical equations relating joint load to deformation.     

Failure load prediction of structural adhesive joints : Part 2: Experimental study

The objective of this study was to determine how the fracture of adhesive joints depends on elastic beam parameters describing the adherends and the applied loads. The basic specimen geometry was the cracked lap shear joint constructed of aluminium alloy with various adherend and bondline thicknesses. Loads were applied in different combinations of bending, tension and shear to generate a failure envelope for each adhesive and specimen geometry. It was found that crack propagation for precracked specimens occured at a critical strain energy release rate but was also a function of the G_I/G_II ratio and the bondline thickness. The experiments also showed that the loads required to propagate a crack in a precracked specimen were always lower than the loads required to break the fillet. Hence, by treating uncracked joints as being cracked, where the fictitious crack tip is assumed to coincide with the location of the fillet, a conservative estimate of the failure load is obtained.     

真空粉末绝热低温贮罐制造的部分工艺方法

在真空粉末绝热低温贮罐的制造过程中、通过吸附器分子筛的活化、夹层真空系统的处理和充装珠光砂等工艺方法的改进,可较大地缩短产品的制造周期并提高产品的质量。     

板壳式换热器设置膨胀节的判定

介绍板壳式换热器的主要特点和应用。当壳体与板束温差较大时,笔者通过对产品开发的生产实践,提出解决板壳式换热器要否设置膨胀节的类似判定方法。     

胶层厚度对拉伸试样应力分布影响的数值分析

运用弹塑性有限元法研究了胶层厚度对承受拉伸载荷的对接接头胶层内应力分布的影响．三维有限元法数值分析的结果表明，随胶层厚度减小，胶层中正应力SZ与剪应力SYZ的分布趋于均匀；而对正应力SY而言，胶层厚度为0．15mm时，其边缘峰值应力最低。     

型钢翼缘狗骨式削弱在型钢混凝土节点的作用

为了防止地震时型钢混凝土节点核心区发生剪切破坏以及梁柱连接焊缝发生脆性断裂,提出对型钢混凝土节点核心区附近梁端型钢的上、下翼缘采取狗骨式削弱,并系统研究翼缘削弱对提高型钢混凝土节点抗震性能的作用.研究表明,由于在梁端型钢翼缘采取狗骨式削弱,不仅能够将塑性铰控制在梁型钢削弱的位置,从而有效地降低了节点核心区所受的剪力以及梁柱连接焊缝的应力;而且能够改善节点塑性铰区的转动能力和抗剪性能,提高节点的延性和耗能能力.     

彩钢岩棉夹芯屋面板、墙面板节点性能研究

为了掌握彩钢岩棉夹芯屋面板、墙面板与檩条的螺钉连接节点抗拉破坏机理,采用理论分析、试验验证及有限元模拟相结合的方法研究了不同钢板厚度及芯材厚度时节点破坏情况.分析结果表明:屋面板节点连接破坏是由于钢板局部屈曲引起的,墙面板则是钢板被冲剪破坏造成的,同时,结合对有限元模拟结果的回归,提出了节点承载力设计公式,可为以后节点设计提供参考.增加岩棉刚度及其与侧向钢板的粘结,或增加钢板厚度对提高屋面板节点极限承载力起着重要作用.     

Moodle在中澳合作办学项目中的应用

Moodle以其经济性和易用性等特点,已在教育领域中得到广泛应用。浙江科技学院在中澳合作办学项目中,基于Moodle的网络教学平台成了联系中澳双方的纽带,为双方教师及学生参与各种教学活动提供了有效的途径。在分析了Moodle课程管理系统的特点和主要功能模块之后,介绍了Moodle在项目中的实际应用情况,指出了在使用这个教学平台过程中存在的不足。