建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。     

三峡地下电站变顶高尾水洞水动力特性

在国内首次应用模型水轮发电机组对三峡地下电站变顶高尾水洞方案进行水力过渡过程试验研究。对水轮机导叶实行分段关闭 ,并求出了二段关闭的最佳拐点 ,试验证实了二段关闭对减小尾水管进口的负压和机组转速上升有明显的作用。通过有关水力参数的测试 ,认为变顶高尾水洞可以满足各项技术要求 ,是一个减少山体开挖、节省投资的新型设计方案。在地下电站中具有广泛的应用前景     

Development of an Enzymic Time Temperature Integrator for Sterilization Processes Based on Bacillus licheniformis α-amylase at Reduced Water Content

ABSTRACT: The thermal stability of Bacillus licheniformis α-amylase at low moisture content was studied, based on isothermal experiments performed in a temperature range 113 to 125 °C. The thermal inactivation was monitored by measuring the decrease in thermal denaturation enthalpy and/or the decrease in enzymic activity on pnitrophenyl-α-D-maltoheptaoside, or on starch as a substrate. Based on enthalpy readings, an enzymic system with a z-value of 10.4 °C was observed when using a relative humidity of 81% at 4 °C. A theoretical study showed that this system could be used as a Time Temperature Integrator (TTI) to monitor the safety of sterilization processes of numerous food products.     

生物除铬(VI)效果及机理探讨

以特定污泥挂膜的自制厌氧生物滤床系统具有良好的去铬(VI)能力。恒流泵最佳流量为47mL/min,外加碳源使废水COD约140mg/L,铬(VI)的浓度由60mg/L左右降到0.5mg/L以下(一级排放标准),需要4h,而对照组(未加碳源)需要14h。铬(VI)浓度由64.66mg/L提高到75.53mg/L时,对系统负面影响甚微,提高到95.47mg/L时,系统出水达标所需时间延长到7.5h。添加微量金属离子与未添加微量金属离子的情况相比,处理效率提高21.26%。分析试验表明:铬(VI)的去除途径可能是由生物还原作用将六价铬还原为三价铬,形成氢氧化铬沉积于微生物表面。     

广州中信商城地下连续墙施工工艺

本文介绍了广州中信商城地下连续墙的施工工艺。该工艺采用膨润土制浆配制方式，施工质量高，效果好。     

黄河下游河道萎缩致灾机理探讨

本文基于水力学原理，结合实体模型试验及原型实测资料分析，探讨了黄河下游河道萎缩的概念、致灾效应和致灾机理。分析表明，河道萎缩是造床过程中河道排洪输沙功能衰退的一种演变现象，其致灾效应是使洪水涨率增大，同流量下洪水水位不断抬升。致灾的现象主要表现在畸型河势增加、工程险情增多、直接造成工程损失及滩区经济损失等。试验研究揭示，主河槽宽度缩窄造成洪水水位涨幅增大，河底平均高程抬升和过水断面面积减小造成洪水水位起涨的基准面抬升是河道萎缩致灾的主要原因。河道萎缩致灾效应的大小与萎缩模式有关，其中以“集中淤槽”模式所形成的致灾效应尤为明显。     

Reaction scheme and kinetic modelling for the MTO process over a SAPO-18 catalyst

A kinetic model for simulation of the MTO process over SAPO-18 catalyst in a wide range of operating conditions has been proposed. The kinetic model predicts the experimental evolution of reaction products with time on stream, which follows three consecutive periods: initiation (where olefin production increases), a period of maximum olefin production and a period in which this production decreases. The kinetic scheme takes into account these three steps that evolve with time on stream: formation of active intermediate compounds, an step where olefins are formed by reaction of oxygenates (methanol/DME) with these intermediates and deactivation of intermediates by degradation to coke. The presence of water in the reaction medium attenuates the reaction rate of these steps. Discrimination of kinetic equations and calculation of the parameters of best fit have been carried out by solving the mass conservation equations of the individual components of the kinetic scheme together with the kinetic equation for deactivation and taking into account the effect of water on the kinetics of each step.     

Photo-Fenton removal of water-soluble polymers

This paper presents the results of experiments carried out in a laboratory-scale photochemical reactor on the photodegradation of different polymers in aqueous solutions by the photo-Fenton process. Solutions of three polymers, polyethyleneglicol (PEG), polyacrylamide (PAM), and polyvinylpyrrolidone (PVP), were tested under different conditions. The reaction progress was evaluated by sampling and analyzing the total organic carbon concentration in solution (TOC) along the reaction time. The behavior of the different polymers is discussed, based on the evolution of the TOC–time curves. Under specific reaction conditions, the formation and coalescence of solid particles was visually observed. Solids formation occurred simultaneously to a sharp decrease in the TOC of the liquid phase. This may be favorable for the treatment of industrial wastewater containing polymers, since the photodegradation process can be coupled with solid separation systems, which may reduce the treatment cost.     

弹力竹节牛仔布织造工艺优化

介绍了弹力竹节牛仔布的生产工艺 ,同时对KT36 8剑杆织机织造该织物的工艺进行了优化研究     

啤酒废酵母干燥工艺设计的研究

该文设计了一套适用于年产量5万吨以上啤酒厂废酵母干燥的生产工艺，提出了设计要点，并对干燥工艺进行了适用性分析。