Melting and crystallization behaviour of elastoplastic semicrystalline copolymers: poly(ether ester)

The melting and crystallization behaviour of an elastoplastic semi-crystalline poly(etherester) has been studied by differential scanning calorimetry. The shape of the melting endotherm is strongly dependent on heating rate and annealing time and results from the sum of simultaneous melting and crystallization phenomena. Samples prepared by different techniques, i.e. by solvent evaporation or by melt extrusion, behave very differently owing to specific crystal morphologies. By applying the Hoffman-Weeks plot, the equilibrium melting temperature has been extrapolated. The Avrami treatment allows the calculation of the index n and of the rate constant K from the isothermal kinetic data.     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

The effect of support morphology on the reaction of oxidative dehydrogenation of ethane to ethylene at short contact times

The oxidative dehydrogenation of ethane is carried out in short contact time reactors over Pt and LaMnO₃ based catalysts supported on a large number of different ceramic substrates (45, 60 and 80 ppi foam monoliths and 200, 400, 600, 900 and 1200 cpsi honeycomb monoliths). Experimental results, obtained under the same conditions at varying the C₂H₆/O₂ ratio, showed that the highest performance in terms of ethylene selectivity and yield is always attained on LaMnO₃ catalysts. Furthermore, the results are significantly influenced by the morphology and cell density of the support, with 45 and 60 ppi foams and 400 and 600 cpsi honeycombs giving the best performance. The experimental results are explained by means of geometrical and fluid dynamic considerations on the support, and by means of a 2D mathematical model, which clearly indicates an optimal intermediate cell density for maximising ethylene selectivity and yield.     

Application of ultrasonic waves in activation of microcrystalline cellulose

In this work, microcrystalline cellulose (MCC) was activated with ultrasonic waves. The influences of ultrasonic treatment on the changes of supramolecular structures and morphology structure were studied by WAXS and SEM. The accessibility of the MCC was characterized by water retention value (WRV) and specific surficial area. The influence of ultrasonic treatment on the reactivity of MCC was investigated through the reaction of MCC being oxidized into 2,3‐diadehyde cellulose (DAC) by periodate sodium. The mechanism of the reactivity change of ultrasonically treated MCC was examined. The results showed that the degree of crystallinity of MCC decreased and the degree of polymerization showed little change after treatment with ultrasonic waves. The morphologial variation of the treated MCC was significant when compared with the untreated MCC, which contribute to the improvement of accessibility. The aldehyde content of DAC prepared from ultrasonically treated MCC was improved from 64.19 to 85.00%, indicating that the regioselective oxidation reactivity of MCC was significantly improved. The aldehyde content was found to first increase with time of ultrasonic treatment to a point, and then decrease as time progressed. In addition, the aldehyde content was found to increase with an increase in ultrasonic power. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of post‐treatments on the properties of porous poly(vinyl alcohol) membranes

Porous poly(vinyl alcohol) (PVA) membranes were prepared by a phase‐inversion method. The influence of chemical crosslinking and heat treatments on the swelling degree, resistance to compaction, mechanical strength, and morphology of porous PVA membranes was extensively studied. The crosslinking degree and crystallinity of the membranes, calculated from IR spectra, increased with the treatment time. The porosity, calculated on the basis of swelling experiments, showed a decreasing trend for heat‐treated membranes but remained almost at a constant value for crosslinked membranes. Such a change was further proved with scanning electron microscopy pictures. The behavior was explained by the rearrangement of PVA chains during the heat‐treatment process, which led to morphological changes in the membranes. The mechanical properties of the porous membranes in dry and wet states were measured, and a great difference was observed between crosslinked and heat‐treated membranes in the dry and wet states. The crosslinked membranes showed good mechanical properties in the dry state but became fragile in the wet state. On the contrary, the heat‐treated membranes were more flexible in the wet state than in the dry state. This change was explained by the turnaround of inner stress in the systems during the swelling process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

On the microhardness testing of electrically stressed poly(phenylene oxide): Polystyrene blends

Microhardness measurements have been performed on untreated (virgin) and electrically stressed, solvent‐cast laboratory‐prepared samples of pure poly(phenylene oxide) (PPO), pure polystyrene (PS), and PPO : PS polyblends with different weight proportions. Results of such measurement on untreated polyblend sample show that microhardness (H_v) increases with increase in the content of PS up to 10 wt %, which attributed to the existence of homogeneous phase morphology. However, this feature is not observable in samples containing higher content of PS. Electrical stress is found to modify considerably the mechanical property of polymer. The effect of electric field on the microhardness of such samples (PPO : PS :: 90 : 10) has been characterized by the existence of a peak. Trapping of charge carriers in electrically stressed samples imparts hardening to the polyblend up to an applied step field of 190 kV/cm. However, the excessive charging beyond this step field value destroys this characteristic. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Shear-induced crystallization of poly(phenylene sulfide)

The crystalline morphology of poly(phenylene sulfide) (PPS) isothermally crystallized from the melt under shear has been observed by polarized optical microscope (POM) equipped with a CSS450 hot-stage. The shish–kebab-like fibrillar crystal structure is formed at a higher shear rate or for a longer shear time, which is ascribed to the tight aggregation of numerous oriented nuclei in the direction of shear. The crystallization induction time of PPS decreases with the shear time, indicating that the shear accelerates the formation of stable crystal nuclei. Under shear, the increase of spherulite growth rate results from highly oriented chains. The melting behavior of shear-induced crystallized PPS performed by differential scanning calorimetry (DSC) shows multiple melting peaks. The lower melting peak corresponds to melting of imperfect crystal, and the degree of crystal perfection decreases as the shear rate increases. The higher melting peak is related to the orientation of molecular chains. These oriented molecular chains form the orientation nuclei which have higher thermal stability than the kebab-like lamellae that are developed later. A new model based on the above observation has been proposed to explain the mechanism of shish–kebab-like fibrillar crystal formation under shear flow.     

Evaluation of improvement of physical and mechanical properties of bamboo fibers due to alkali treatment

Bamboo strips treated with caustic solutions of different concentrations, e.g., 5%, 10%, 15%, 20%, 25%, and 50%, were subjected to mechanical testing giving stresses on tensile strength, percent elongation at break, flexural strength, flexural modulus, and toughness. The change in average density was ?15%, and the weight loss value shows a maximum of 21.94% at 50% alkali treatment. The mechanical properties of bamboo strips increase steadily with increasing concentration of caustic soda, showing a comparable increased value at 15 and 20%, and then exhibiting a gradual fall. The percent elongation at break corroborates these observations showing a continuous decreasing trend. The properties under investigation exhibit a clear transition in between 15 and 20% alkali concentration. The morphology of strips was studied by scanning electron microscope and polarizing light microscope. The crystal structure of both untreated and treated strips was compared by XRD analysis. In both cases, the breakdown of the crystal structures of the cellulose fibers and the recrystallization or reorientation of the degraded chains that are devoid of hemicellulose are quite apparent. However, at a very high concentration (to the extent of 25%) the breakdown of structure predominates much more over the reorientation or recrystallization. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Modeling the effect of pigment morphology on the dynamic compression of coating layers using DEM

In the present paper, discrete element method (DEM) was employed to investigate the effect of pigment morphology on packing dynamics and compressive behavior of paper coating layers in calendering process. Spherical, platy, and needle-like particles, representing GCC, delaminated clay, and aragonite PCC pigments, were considered in this study. For each particle shape, the compression of coating structures formed by mono-sized and poly-dispersed pigments were modeled. Stress–strain behavior of the coating layers and in-plane and out-of-plane movements of the pigment particles during the compression were computed under the same maximum compressive stress. Simulation results revealed that the in-plane movements of the pigment particles during compression in the calender nip were small in magnitude (<0.35 μm). These findings help to better understand the smoothening phenomena of coating structures during the calendering process.