降凝剂对高蜡稠油的改性效果及机理研究

实验研究了工业品原油降凝剂WHP改善含蜡56.9%、其中96.6%为正构烷烃的胜利郑王庄稠油流动性的效果。WHP含乙烯/醋酸乙烯/乙烯醇嵌段聚醚三元共聚物30%-35%。在60℃将WHP加入稠油中,测定其凝点和32℃、0-42.6 s^-1范围5个剪切速率下的黏度,均随WHP加量的增加（50-300 mg/L）而降低,200 mg/L为最佳加量,在该加量下0.32 s^-1黏度由34.16 Pa·s降至79.2 mPa·s,凝点（℃）、屈服值（Pa）、稠度系数（Pa·s^n）分别由49.0、32.42、31.57降至39.5、0.1297、0.02142,流型指数由0.1176升至0.9790。由黏温曲线求出,加入200mg/L WHP使该稠油析蜡点由65℃降至58℃,反常点由70℃降至50℃。根据空白和加剂原油扫描电镜照片显示的蜡晶形态,利用共晶机理分析讨论了WHP这种高分子表面活性剂的降凝、降黏、改善流动性的作用。图3表3参5。     

图像处理中自适应数学形态学的研究

实际图像处理中当视场的变化引起目标变形时,固定大小的形态学算子很难达到较好的处理效果。研究了利用距离变换自适应地调整结构元大小的方法,即根据图像的不同位置来调整结构元素的大小,从而实现图像的形态学运算,并由此推导出了快速计算方法,最后测试了这种新算法的有效性。实验结果表明,该算法取得了较为理想的效果。     

低碳微合金钢中的晶内铁素体及组织控制

回顾和评述了晶内铁素体的发现、发展及其与组织控制的关系.介绍了晶内铁素体的形核机制和影响晶内铁素体形成的因素,讨论了晶内铁素体的三维形态和长大动力学,并从以上几方面分析了晶内铁素体对低碳微合金钢组织细化的重要作用和影响.     

复合聚合物微粒乳液的制备与应用

对种子乳液聚合中加料方式、单体亲水性、引发剂等因素对复合微粒聚合物形成的影响作了介绍 ,总结了聚合物微粒形态预测的热力学和动力学方法。同时 ,讨论了复合聚合物微粒设计的原理并评述了其应用情况     

Melting and crystallization behaviour of elastoplastic semicrystalline copolymers: poly(ether ester)

The melting and crystallization behaviour of an elastoplastic semi-crystalline poly(etherester) has been studied by differential scanning calorimetry. The shape of the melting endotherm is strongly dependent on heating rate and annealing time and results from the sum of simultaneous melting and crystallization phenomena. Samples prepared by different techniques, i.e. by solvent evaporation or by melt extrusion, behave very differently owing to specific crystal morphologies. By applying the Hoffman-Weeks plot, the equilibrium melting temperature has been extrapolated. The Avrami treatment allows the calculation of the index n and of the rate constant K from the isothermal kinetic data.     

STUDY ON GIS BASED PREDICTION SYSTEM FOR RADIO WAVE PROPAGATION IN UBAN REGION

In this letter, an integrated application of the prediction for radio wave propagation with the Geographic Information System (GIS) is presented and a real prediction system based on GIS is implemented.     

硅酸铋晶体的蚀像形貌

本文研究了提拉法生长的硅酸铋晶体(BSO)的蚀像形貌,比较了{100},{110},{211},{111}面族的腐蚀像特征和腐蚀速度,并用周期性键链(PBC)的形貌理论分析了腐蚀形貌。通过蚀像形貌特征便可方便地进行晶体定向,准确地确定各族晶面之间的相对位置和极轴的方向等。     

Properties of ligno‐cellulose fiber Hildegardia

Studies on some properties such as the density, the degradation temperatures, the morphology and the spectral features of the ligno‐cellulose fiber Hildegardia were carried out in both untreated and alkali treated form. The fibers are found to have good morphology and moderate initial and final degradation temperatures. On alkali treatment, the lignin was found to be eliminated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2216–2221, 2002     

局部施肥对植株生长及根系形态的影响

本文论述了局部施肥对植株地上部与地下部的影响。局部施肥促进了施肥区根系的发达 ,第一侧根与第二侧根较多 ,根的吸收表面积增多 ,根鲜重增加 ,对养分的吸收能力增强 ,但整个根系与地上部的干鲜重下降。     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry