双重孔隙介质油藏中的吸渗排油作用

利用美国SSI公司研制的COMPN模拟软件对双重孔隙介质油藏一种重要的开采机理 吸渗排油进行了模拟研究,考察了一个基质岩块为四周裂缝所包围时.在驱动压力和毛管压力的不同平衡(驱动压力和毛管压力的相对大小)关系下的水驱油采收率和水驱油效率的变化规律.     

网壳结构内扩安装法施工内力特性分析

本文针对目前国内常用的网壳内扩安装法，全过程跟踪分析了构件在用内扩法安装期间的施工内力特性及其变化规律，得出了网壳结构设计计算必须考虑施工内力的影响等重要结论。     

各向加权异性有限元法在不可压粘性流动计算中的应用

本文利用各向异性张力有限单元，考虑到其独特的性质，提出了一种各向加权异性的算法，即在不同方向采用不同连续性的插值函数，然后再在原连续性较弱的方向以连续性较强的插值函数计算，最后把两次计算的结果加权处理。这种方法可以适应两个方向连续性要求不同或相同的各种情况，即克服了一般各向异性张力有限单元的局限性，又大大减少了存贮量和计算量。     

弹性杆与水下壳体接触冲击的冲击力计算研究

对弹性杆与水下壳体接触冲击问题进行了研究，用有限元法模拟壳体，边界无法模拟无限域流体，通过温面上的耦合条件进行联立求解，文中给出了典型算例，并进行了有关讨论。     

Measurements of Stress Intensity Factors of an Interface Crack Under Mixed Mode Loading

The optical method of caustics has been utilised to measure both the stress intensity factor for a crack lying along the interface of an aluminium/epoxy bimaterial specimen, and the mode mixity arising from the difference in the elastic properties across the interface. Measurements were carried out by using a novel modification to the method whereby caustics are produced and measured from both sides of the specimen, so compensating automatically for the distortion induced in the specimen due to misaligned loading fixtures. A flat reflective surface across the interface was obtained by adhering a reflective coating to the specimen. Verification that this coating does not affect measurement accuracy was obtained by comparing stress intensity factors measured from coated and uncoated monolithic aluminium specimens where good agreement was found to exist between both measurements.     

滁州市农贸市场超长预应力楼盖的设计分析

滁州市农贸市场超长预应力楼盖温度应力有限元分析及设计原则。     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

快干性瓦楞纸箱粘合剂的研制

本文叙述了快干性瓦楞纸箱粘合剂的配制及工艺过程。实验结果表明，该粘合剂具有快的干燥速度和良好的性能     

提高脲醛树脂胶质量的途径

根据生产实践,论述了原料和工艺条件等对提高脲醛树脂胶质量的影响。其中原料以尿素、甲醛、各种改性剂为主,工艺条件包括反应物配比、反应温度、介质pH值、终点控制方法等。     

石油钻机提升系统穿绳方法研究

目前国内外钻机大绳一般采用顺穿法或花穿法。分析了2种穿绳方法的受力特点,大绳顺穿时游车的受力不平衡,会发生倾斜和摆动;采用大绳花穿方法,避免了游车的倾斜和摆动,但造成大绳入轮槽的倾角大,大绳易脱槽。顺穿法一般在电动钻机上采用,主要考虑到电控操作提升系统比较平稳;花穿法一般在机械钻机上使用,以受力平衡来缓解气控操作带来的冲击载荷的影响。为了克服这2种穿绳方法的不足,提出了两行双联滑轮组顺穿法和双联滑轮组顺穿法,可以提高安全性,减少磨损。