川中丘陵区一种新型小流域径流输沙模型的建立与应用

径流输沙模型对定量评价水沙的输出响应具有重要的意义。本研究在已有研究成果的基础上，通过对四川盐亭县林山西沟小流域的径流、泥沙进行现场观测与分析，提出含沙量单位线的定义及其确定方法，建立了适应该小流域的径流输沙模型。并应用实测资料进行比较，表明模型的模拟结果可靠，模拟过程确定性系数达0．8以上，为川中丘陵区小流域径流输沙过程的预测预报提供了一个新方法。     

三峡水电站坝后钢衬钢筋混凝土压力背管的非线性有限元分析

采用钢筋混凝土非线性有限元方法，对三峡水电站钢衬钢筋混凝压力管道结构进行了计算，求得了各种钢材配置下的荷载效应并进行了相应的分析。     

伪波阻抗反演在准噶尔盆地永进油田储层描述中的应用

永进油田目的层产状平缓,断层不发育,储层厚度小、埋深大、描述困难。运用伪波阻抗技术对该区的储层进行了研究,取得了较好的效果。     

拱坝三次样条曲线拱圈线型及优化研究

建立拱坝拱圈三次样条曲线模型，根据非线性规划町行域与最优解的理论。比较了抛物线、椭圆、双曲线和三次样条曲线线型的优劣，并采用复合形法对这些线型的拱圈进行了优化。结果表明，三次样条曲线拱圈最优。     

一种广义水驱特征曲线的建立

广义水驱特征曲线能描述综合含水储量采出程度呈多种不同的凸、S、凹曲线类型。根据油水两相渗流原理，从归一化的油水相对渗透率出发，建立起累积产油、累积产水与综合含水率的积分相关关系，进而建立了累积产油、累积产水与归一化的油水相对渗透率的关系。通过构建积分函数，利用公式形式类比，建立了更一般形式的广义水驱特征曲线。理论分析和实例计算表明，所建立的广义水驱特征曲线与实际数据线性相关性更强，结果更可靠。     

Influence of Ni Interlayers on the Mechanical Properties of Ti6Al4V/(WC-Co) Friction Welds

Ni interlayers were introduced prior to dissimilar friction welding of Ti6Al4V base material to three cemented carbide substrates. The fracture strength of Ti6Al4V/(WC-6 wt% Co) welds were poor and were markedly improved when 20-µm thick Ni interlayers were introduced prior to dissimilar friction welding. These results were only produced when the (WC-6 wt% Co) cermet was electroplated prior to friction welding. When the Ti6Al4V alloy was electroplated prior to friction welding, fractured WC particles and cracking were observed in the (WC-Co) carbide substrate. The fracture strengths of Ti6Al4V/(WC-11 wt% Co) and Ti6Al4V/(WC-24 wt% Co) welds were not improved when 20-µm thick Ni interlayers were introduced prior to friction welding. During mechanical testing, the Ni layer retained at the dissimilar joint interface created a region of weakness.     

硬地层定向井中几种侧钻方法的灵活应用

在川渝地区，钻定向井、水平井必然要面对地层岩性变化大、硬度高等复杂地质情况，常常会遇到因井下复杂、事故、修改地质目标等原因需要填井侧钻。侧钻的方法不同，侧钻的成功率和效率差异很大。文中分析了川渝地区近几年硬地层定向井、水平井侧钻效率不高、有时甚至失败的原因，归纳总结了近几年常用的几种侧钻方法的施工效果，提出要根据具体条件灵活应用这几种侧钻方法。     

First Harmonic (2f) Characterisation of Resonant Frequency and Q-Factor of Micromechanical Transducers

In this paper, the response to the first harmonic component (2f) of the electrostatic force in single terminal driven electrostatic comb-drive and parallel-plate drive was used as a signal to extract device parameters, namely, the Q-factor and resonant frequency instead of the fundamental (1f) resonance response. It is shown that the difficulty in motional measurement due to electrical cross-talk (parasitics) using 1f measurement can be overcome with a higher signal-to-noise ratio of the 2f signal. Both atmospheric (low-Q) and reduced pressure environment were investigated using off-chip electronics and lock-in amplifier. The measurements were done on the electrostatic comb-drive and capacitive parallel plate sensing plates that form the two core modules of a yaw rate sensor (dual-axis resonator). The effects of AC and DC bias voltages on the measured response have been investigated. Experimental amplitude and phase response data have been analysed using the Lorentzian curve-fit, Resonance Curve Area (RCA) method, the half-power bandwidth method (3 dB) and the Nyquist plot for data fitting and determination of the Q-factor and resonance frequency.     

A modified rainflow counting method

The rainflow counting method is commonly recognized to be a good cyclic counting method in fatigue life prediction and for testing engineering components and structures. However, it has some shortcomings, which are pointed out in this paper in connection with the analysis of the stress-strain response. A modified rainflow counting method is presented. Case studies show that all the cycles really existing in the stress-strain response that cannot be counted by the rainflow counting method can be counted by the modified rainflow counting method. So it can be said that the modified rainflow counting method is a more reasonable cycling counting method than the traditional rainflow counting method.