A direct estimate of JIc from the load versus load-line displacement record

The purpose of this study is to examine the current standard fracture toughness test procedure to determine if there could be an easier method to get a J_Ic value from the test record. The current method for determining J_Ic involves a detailed computational and construction procedure. The objective in this study is to simplify the analysis for the determination of J_Ic. The results of this study show that the load and displacement record for a fracture toughness test can be used to directly estimate a J_Q value, a provisional value for fracture toughness, J_Ic. The J value taken at the maximum load point can be used along with an adjustment factor to estimate a J_Q value. This J_Q estimate is close to the one obtained from the construction procedure of ASTM Standard E 1820. When a unit‐sized specimen is tested, that is, a specimen with a width of 50 mm and a thickness of 25 mm the maximum load point provides a direct estimate of J_Q. Other sizes require a size adjustment factor, which is simply a square root relationship between the width of the test specimen and a unit width. The proposed new method of estimating J_Q is simple in concept and requires a minimum number of calculations. It appears to produce values of J_Q which are comparable to those obtained from the ASTM E1820 construction procedure and may produce less scatter.     

泡沫酸化工艺对川中低压裂缝性油藏适应性的认识

针对川中油田经过多年的消耗式开采,各主产油田压力很低,增产改造的难度增大的发展现状,提出应用泡沫酸化工艺技术在川中低压油层增产改造的技术方案,其中分析了泡沫酸的物理特性、其在地层优良的渗流特性(滤失小、酸岩反应速度慢、返排迅速等优点),并进行了泡沫酸液体系的室内配方研究,提出了工艺设施的矿场配套研究内容.得出了泡沫酸化工艺对川中低压裂缝性油藏改造具有很强的适应性,具有推广应用的价值.     

朝阳沟裂缝性低渗透油田井网适应性研究

通过对比分析朝阳沟裂缝性低渗透油藏与裂缝主方向分别成11.5°和22.5°的两种不同井网的开发效果,表明与裂缝成11.5°的井网与裂缝匹配性较差,开发效果相对较差。并从油藏的水驱控制程度、压力传导情况、采收率及经济效益等方面研究评价了朝1.55区井网的适应性,为指导油田的加密调整,在技术和经济两方面综合评价确定了合理的井距和井网密度,并针对朝1-55区的地质特征,提出了井网和注水方式调整办法,在朝55区块实施后,取得了较好的现场试验效果。     

连轧机用人字轮齿轴断裂失效分析

用宏观断口分析、化学检验、力学性能测定、低倍检查、金相组织及夹杂物评定鉴别、受力分析及强度寿命定量估算的方法，对人字轮被动齿轴端断裂失效原因进行分析，并提出改进措施。     

65MnTi盘条拉拔过程中出现断裂的原因分析

分析检验拉拔过程中发生断裂的65MnTi盘条的金相组织和断口形貌，得出结论；65MnTi金条发生断裂的原因是热轧后冷却速度过快，金相组织中出现了低温转变组织──马氏体组织；而理想的组织应为京氏体；并且最佳冷却速度为5℃／s左右。     

Experimental and numerical investigation of fracture in double-edge notched steel plates

Double-edge notched (DENT) steel plates were pulled until complete fracture and several experimental observations were made (using profilometry and scanning electron microscopy). The essential work of fracture (EWF) model was found to be well verified. Numerical simulations—up to the maximum load only—of some experiments were performed using the finite element method (FEM), and incorporating geometric and material non-linearities (large deformation elasto-plasticity). Some experimental measurements were compared with the corresponding numerical computations and excellent agreement was found.     

THE FRACTURE MECHANISM OF 475°C EMBRITTLEMENT IN A DUPLEX STAINLESS STEEL

The mechanism of “475°C embrittlement” of a duplex stainless steel was investigated using finite element modelling of the stress distribution at brittle fracture initiation. Brittle fracture initiated at a critical shear stress, which increased with ferrite hardness. The fracture stress was affected by the duplex microstructure. Fracture was nucleated by deformation twins, which were identified using electron back-scatter diffraction. The ductile-to-brittle fracture transition was sensitive to age-hardening and could be described simply by the effect of age-hardening and test temperature on the yield stress.     

双重孔隙介质油藏中的吸渗排油作用

利用美国SSI公司研制的COMPN模拟软件对双重孔隙介质油藏一种重要的开采机理 吸渗排油进行了模拟研究,考察了一个基质岩块为四周裂缝所包围时.在驱动压力和毛管压力的不同平衡(驱动压力和毛管压力的相对大小)关系下的水驱油采收率和水驱油效率的变化规律.     

On basic definitions of unified fracture mechanics terminology

The adoption of unified fracture mechanics terminology (UFMT) will promote efficient communication between specialists in different fields of fracture research, harmonization of national and international standards relating to fracture mechanics, and last but not least improvement of the existing methodology for teaching and education in fatigue and fracture. In this paper the definitions of some basic and related terms included in different standards on fracture mechanics terminology are confronted with one another. Alternative definitions of the same terms are offered. By this strategy the author tries to show that the definitions of basic and related terms appropriate for the UFMT should emerge as a consequence of harmonizing a crack model with an actual crack and then both taken together with a fracture model, laboratory test methods, and failure assessment codes.Published in Problemy Prochonsti, No. 1, pp. 17–29, January, 1996.This paper is published as a matter of discussion.     

A Review of Dynamic Fracture Studies in Functionally Graded Materials

Abstract:  This article presents a review of dynamic fracture studies on functionally graded materials. A brief literature review on the fracture mechanics of graded materials is presented first. This is followed by a discussion on the higher-order asymptotic analysis of the transient elastic field surrounding the tip of a dynamically growing crack in a functionally graded material. A comprehensive experimental study of dynamic crack growth in model functionally graded material using the optical method of reflection photoelasticity and high-speed photography is then presented. The results are analysed to establish a generalised relationship between the crack velocity and the dynamic mode-I stress intensity factor (SIF). This relationship is found to be unique and is distinctly different from that previously established for the matrix material (polyester). Finally, an innovative experimental procedure is used to demonstrate the necessity of employing a fully transient stress-field representation in the analysis of optical data for an accurate prediction of the dynamic SIF history.