Binodal and spinodal curves: a simulation for various high polymer mixtures

Flory's equation-of-state theory has been used to predict the lower critical solution temperature behaviour of polymer—polymer mixtures. The spinodal phase boundary of numbers of high molecular weight polymer mixtures have been previously simulated using this theory. In this paper a procedure for simultaneous predictions of the binodal and the spinodal curves by equating the chemical potential of each component in the mixture is presented. The method is tested for five different mixtures. The effects of the binary and pure component state parameters on the simulated curves are discussed and the simulated phase diagrams are compared with the experimental cloud point curves. It is found that in most cases the results are more consistent with the cloud point curve being closer to the spinodal curve than the binodal.     

Fundamentals of stability testing

The principles on which stability tests are based are reviewed. The need to differentiate between product stability and product-container compatibility is emphasized. Recognition of this distinction is fundamental to the efficient organisation and execution of stability tests.
Attention is also drawn to the desirability of having for every product a release specification with which it must comply when manufactured and a broader check specification with which it must comply throughout its shelf-life.
Test methods and the interpretation of the data accrued throughout a test are also discussed.
It is concluded that stability tests should not be conducted in accordance with a standardized routine pattern but that the objectives of each test should be defined and the test designed to achieve those objectives in the most efficient way.
Les regles fondamentales des essais de stabilite     

盐家油田油水井结垢原因探讨

对地层温度65～75℃的盐家油田油水井近井地带、井底、井筒发生严重结垢的原因进行了分析探讨。7口油井采出的地层水均为NaCO3型水．矿化度6．4～10g／L，HCO3浓度高（1．6～3．7g／L），Ca^2＋＋Mg^2＋浓度较低；1口水源井水及1口水井注入水为CaCl2型水，矿化度32～33g／L，Ca^2＋＋Mg^2＋浓度高（3．1～3．8g／L）而HCO3浓度低；采用CaCO3饱和指数法和CaSO4热力学溶解度法预测，在70℃下所有水样均有CaCO3结垢趋势，除3口油井采出的地层水外，均有CaSO4结垢趋势。3口油井采出的地层水与水源水在25℃按不同比例混合后，悬浮物含量大幅度上升。在70℃放置7天后再次大幅度上升，烘干的悬浮物易溶于稀盐酸．其主要成分为碳酸盐．说明注入水、地层水不配伍。1口电泵采油井和1口注水井油管垢样含盐酸可溶物（碳酸盐）超过90％。讨论了碳酸盐、硫酸盐垢的生成条件：温度、压力及pH值。图1表4参3。     

影响喷气燃料与橡胶相容性的因素

采用几种具有不同初始物理性能及不同丙烯腈含量、不同硫化剂和硫化程度的丁腈橡胶，考察了其配方和物理性能对采用不同工艺条件生产的喷气燃料的相容性。结果表明，喷气燃料与橡胶的相容性不仅与喷气燃料的加工工艺有关，而且与橡胶的组成及其制备工艺有关。采用非加氢工艺生产的喷气燃料与橡胶的相容性好于采用加氢工艺(特别是加氢裂化工艺)生产的喷气燃料。橡胶材料的初始力学性能的好坏并不完全决定其与喷气燃料相容性的好坏，橡胶材料的耐过氧化物侵蚀能力才是影响相容性好坏的主要因素。橡胶的组成和其制备工艺决定了橡胶在喷气燃料中萃取物的数量和组成，不同萃取物的综合作用给相容性带来不同程度的影响。用硫作硫化剂的橡胶虽然原始强度低于用过氧化物作硫化剂的橡胶，但前者与喷气燃料的相容性却远好于后者。     

Thermodynamic state of reinforced interpenetrating polymer networks

The free energies of mixing of two networks in the interpenetrating polymer network based on crosslinked polyurethane and poly(ester acrylate) have been determined by the vapour sorption method. It was established that the constituent networks in the IPN are not miscible. The introduction of fillers of different chemical nature increases the compatibility. The thermodynamic affinity of the fillers to the individual networks and IPN was estimated. It was established that when the free energy of interaction of one or both components of the IPN with the filler is negative, reinforcement leads to the formation of a compatible and equilibrium system. For fillers having no affinity to the polymers, compatibilization is observed, which is connected with slowing down of phase separation in the system in the presence of filler.     

共混合金力学性能的研究 Ⅲ.CPP对PVC共混体系力学性能的影响

将ＰＰ氯化后作为ＰＶＣ共混体系的刚性体分散相，旨在改善高分子合金的相容性，ＤＳＣ实验表明，ＣＰＰ（氯化聚丙烯）与ＰＶＣ的相容性比ＰＶＣ与ＰＰ的好。在用弹性体增韧的ＰＶＣ／ＣＰＥ和ＰＶＣ／ＡＢＳ共混体系中加入刚性体ＣＰＰ后，随着ＣＰＥ、ＡＢＳ用量的增加，共混合金的冲击强度增加，并且由刚性的ＣＰＰ的加入所产生的冲击强度最大值的幅度也有所提高，其趋势是ＣＰＥ、ＡＢＳ用量越多，共混合金冲击强度值达到最大值时所需ＣＰＰ的量越多，增加的幅度也越大。ＣＰＰ对共混合金的拉伸屈服强度和断裂伸长率的影响比较小。     

A new approach to the decomposition of Boolean functions by the method of <Emphasis Type="Italic">q</Emphasis>-partitions. III. Joint decomposition of a function system

The paper considers the set-theoretical approach to the joint decomposition of systems of Boolean functions of variables specified in different representation forms. The approach is based on the method of q-partitions of conjuncterms and concept of decomposition clones. Theorems on joint decomposition of a system of full and partial functions are formulated. The approach is illustrated by examples. Parts I and II of this article are published in No. 5 (2001) and No. 1 (2002). __________ Translated from Kibernetika i Sistemnyi Analiz, No. 2, pp. 39–58, March–April 2007.     

试论开关电源的电磁干扰

开关电源因体积小、功率因数较大等优点而在通信、控制、计算机等领域广泛应用,但其产生的电磁干扰在一定程度上限制了它的使用。文中简单介绍了开关电源电磁干扰的相关概念,分析了开关电源电磁干扰产生的机理,介绍了实施开关电源电磁兼容的方法,并结合实际实用,介绍了开关电源目前常用的抑制干扰的具体措施。     

掏挖与岩石锚杆复合型基础上拔承载机理和影响因素研究

针对掏挖与岩石锚杆复合型基础上拔承载机理不明确的问题,基于现场试验工况,利用Plaxis3D有限元软件建立复合型基础抗拔承载模型,研究其上拔承载机理。在此基础上,研究了土体弹性模量、岩体弹性模量、土体黏聚力对复合型基础各部分的承载影响,分析了掏挖基础和岩石群锚基础的承载力发挥情况、上拔变形、塑性区开展,并给出了复合型基础的改进方案。结果表明:上拔变形刚度较大的岩锚基础对复合型基础的承载极限状态起控制作用;掏挖基础和岩石锚杆基础的上拔变形协调性是影响复合型基础承载力发挥的关键;适当增加掏挖基础嵌入岩石的深度可有效提高复合型基础的抗拔承载力。     

Radiation-induced modification of polyurethane with hydroxyethyl methacrylate: blood compatibility

An attempt is made to develop the hydrophilic grafting of polyether urethane urea with hydroxyethyl methacrylate (hema) using⁶⁰Coγ-irradiation for achieving optimum hydrophilic/hydrophobic property needed towards blood compatibility. Contact angle method and platelet adhesion from calf’s blood are used to determine the suitability of these modified surfaces.