Design and experimental investigation of the high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler

The development of a high cooling power and high efficiency 4.2 K two stage G-M cryocooler is critically important given its broad applications in low temperature superconductors, MRI, infrared detector and cryogenic electronics. A high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler has recently been designed and developed by ARS. The effect of expansion volume rate and operation conditions on the cooling performance has been experimentally investigated. A typical cooling performance of 1.5 W/4.2 K has been achieved, and the minimum temperature of the second stage is 2.46 K. The steady input power of the compressor at 60 Hz is 6.8 kW, while the operation speed of the rotary valve is 30 rpm. A maximum cooling power of 1.75 W/4.2 K has been obtained in test runs.     

一种基于FPGA的可变速率帧结构设计与实现

在简述V.35接口的基础上针对V.35接口速率可变的应用需求提出了一种速率可变的帧结构,该帧结构可支持N×64kb/s(3≤N≤32)速率,从而在V.35接口上实现了多种速率的低速业务传输.     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

冷轧平整机机前甩尾轧制工艺的开发与应用

本文介绍了柳钢冷轧板带厂1550 mm单机架平整机机前甩尾轧制的工艺。改进前轧制每卷钢卷生产效率低,钢卷成材率低,改进后生产效率、成材率明显提高,部分规格的钢卷能实现带尾剪切长度为零。     

Slow strain rate technique for studying hydrogen induced cracking in 34CrMo4 high strength steel

Alloy hardened steels offer excellent combination of mechanical properties, hardenability and corrosion resistance. 34CrMo4 is a medium carbon, low alloy steel widely used due to a good combination of high-strength, toughness and wear resistance. However, this steel experiences hydrogen embrittlement (HE), a complex phenomenon depending on the composition and microstructure. This work estimates de loss of the mechanical properties caused by hydrogen in electrochemically H-charged specimens in absence of mechanical stress but also, at low strain rate and constant load. H-charging for 2 and 6 h induce YS losses of about 40% and 71% and UTS losses of 39% and 59%, respectively. The synergistic effect of the stress and the H-charging process leads to a higher loss, 91%, and a faster brittle fracture even though hydrogen content is similar to those firstly H-charged and then tested in air.     

机载通信电台通电老炼检测系统设计与实现

为保证航材备件的完好率，解决仓储机载通信电台长期不通电导致的装备性能下降甚至出现故障的问题，综合运用自动测试、虚拟仪器、面向信号设计等技术，以计算机为核心，以PXI仪器、GPIB仪器为依托，以多种总线接口为纽带，构建了一种可靠性高、通用性好、操作简便、可扩展性强的自动化通电老炼平台。通过在航材仓库中使用，证明该电台老炼检测系统降低了仓储通信电台的失效率，提高了仓储电台的完好率。     

Viscoelastic Behavior of Synthesized Liquid Soaps and Surface Activity Properties of Surfactants

In the present work, a rheological study of liquid soaps prepared from different mixture of surfactants as a function of surfactant type and concentration was performed. The curves of shear stress vs. shear rate and viscosity vs. shear rate were recorded at constant temperature, 294 ± 0.1 K. The surface activity properties were also studied. The results of the study showed that values of surface tension, γ, were in the range 31–40 mN m⁻¹ and the critical micelle concentration (CMC), was of the order 10⁻⁴ mol L⁻¹. The calculated maximum surface excess, Γ_max, varied from 2.40 to 3.66 μmol m⁻², while minimum area per molecule, A_min, varied from 41.1 (for amphoterics) to 81.4 Ų (for nonionic surfactants). The standard free energy of micellization, −29.8 and −29.3 kJ mol⁻¹ for anionic and amphoteric surfactants, respectively, were while values for nonionic surfactants varied between −31.8 and − 30.3 kJ mol⁻¹. The free energy of adsorption, was the lowest for amphoteric surfactants (−37.9 kJ mol⁻¹), followed by anionics (−40.4 kJ mol⁻¹) and nonionics (−43.34 to −46.84 kJ mol⁻¹), indicating that micellization process is spontaneous in the examined medium. The synthetized liquid soaps show pseudoplastic behavior and they achieved pipe flow. The results of this research indicate that flow behavior was affected significantly by the ionic charge of the surfactant and the ionic strength of the formulation, suggesting that the flow behavior could be changed by manipulating the choice of the surfactant and salinity. The pH value of all liquid soaps examined were weakly acidic, in the range of 5.0–6.4.     

Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

Application of higher order spectral features and support vector machines for bearing faults classification

Condition monitoring and fault diagnosis of rolling element bearings timely and accurately are very important to ensure the reliability of rotating machinery. This paper presents a novel pattern classification approach for bearings diagnostics, which combines the higher order spectra analysis features and support vector machine classifier. The use of non-linear features motivated by the higher order spectra has been reported to be a promising approach to analyze the non-linear and non-Gaussian characteristics of the mechanical vibration signals. The vibration bi-spectrum (third order spectrum) patterns are extracted as the feature vectors presenting different bearing faults. The extracted bi-spectrum features are subjected to principal component analysis for dimensionality reduction. These principal components were fed to support vector machine to distinguish four kinds of bearing faults covering different levels of severity for each fault type, which were measured in the experimental test bench running under different working conditions. In order to find the optimal parameters for the multi-class support vector machine model, a grid-search method in combination with 10-fold cross-validation has been used. Based on the correct classification of bearing patterns in the test set, in each fold the performance measures are computed. The average of these performance measures is computed to report the overall performance of the support vector machine classifier. In addition, in fault detection problems, the performance of a detection algorithm usually depends on the trade-off between robustness and sensitivity. The sensitivity and robustness of the proposed method are explored by running a series of experiments. A receiver operating characteristic (ROC) curve made the results more convincing. The results indicated that the proposed method can reliably identify different fault patterns of rolling element bearings based on vibration signals.     

Computational studies on the radiative and nonradiative processes of luminescent N-heteroleptic platinum(II) complexes

Three N-heteroleptic Pt(II) complexes, [Pt(C^C)(O^O)] [O^O = acetylacetonate, C^C = 1-phenyl-1,2,4-triazol-5-ylidene (1), C^C = 4-phenyl-1,2,4-triazol-5-ylidene (2), C^C = 2-phenylpyrazine (3)] have been investigated with density functional theory (DFT) and time-dependent density functional theory (TDDFT). The radiative decay rate constants of complexes 1–3 have been discussed with the oscillator strength (f_n), the strength of spin–orbit coupling (SOC) interaction between the lowest energy triplet excited state (T₁) and singlet excited states (S_n), and the energy gaps between E(T₁) and E(S_n). To illustrate the nonradiative decay processes, the transition states between triplet metal-centered (³MC) and T₁ states have been optimized and were verified with the calculations of vibrational frequencies and intrinsic reaction coordinate (IRC). In addition, the minimum energy crossing points (MECPs) between ³MC and ground states (S₀) were optimized. At last, the potential energy curves relevant to the nonradiative decay pathways are simulated. The results show that complex 3 has the biggest photoluminescence quantum yield because the complex 3 has the biggest radiative decay rate constant and the smallest nonradiative decay rate constant in complexes 1–3.