微型灌注桩托换技术在地基基础加固工程中的应用

因场地淤泥等软土层深厚,在填方荷载作用下,软弱土层产生固结沉降,引起局部构筑物的不均匀沉降,发生结构破坏。采用微型灌注桩加固满足现场各个限制条件的要求,达到了加固目的。     

Effects of temperature, ammonium and glucose concentrations on yeast growth in a model wine system

In enology, alcoholic fermentation is a complex process involving several mechanisms. Slow and incomplete alcoholic fermentation is a chronic problem for the wine industry and factors leading to sluggish and stuck fermentations have been extensively studied and reviewed. The most studied cause of sluggish and stuck fermentation is the nitrogen content limitation. Nevertheless, other factors, such as temperature of fermentation and sugar concentration can affect the growth of yeasts. In this study we modelled the yeast growth‐cycle in wine model system as a function of temperature, sugar and ammonium concentrations; the individual effects and the interaction of these factors were analysed by means of a quadratic response surface methodology. Cell concentrations and weight loss were monitored in the whole wine fermentation process. The results of central composite design show that lower is the availability of nitrogen, higher is the cell growth rate; moreover, initial nitrogen concentration also influences survival time of Saccharomyces cerevisiae.     

Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

NPCDP／PET复合仿毛纤维纺丝工艺研究

应用复合纺丝方法并通过加弹、空气变形等措施使ＮＰＣＤＰ／ＰＥＴ异染异收缩纤维获得优良的毛性感。简要介绍了复合纺丝的工艺路线，讨论了纺丝温度、压力、干燥工艺、拉伸条件对可纺性的影响，并明确了变形工艺对复合纤维的影响作用。制得的ＮＰＣＤＰ／ＰＥＴ复合纤维物理力学性能符合后加工要求，织物的缓弹回复角达３０５度。     

On the mechanical behavior of aluminum alloys reinforced by long or short alumina fibers or SiC whiskers

This study was initiated to examine the dispersion of longitudinal and transverse waves in metal matrix composites in order to obtain the dynamic elastic modulus and to evaluate various models for predicting the composite's macroscopic elastic constants from the properties of its constituents. The materials chosen for this investigation were alumina continuous fibers on the one hand and alumina and SiC short fibers on the other hand, all embedded in an aluminum alloy matrix. In addition, some indications have been obtained experimentally for the acoustoelastic effect in the composite.     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

水对植物纤维水泥复合板生产的影响

研究了水对植物纤维水泥复合板性能的影响。选择合适的水分可以提高板材静弯曲强度,减小板材变形。     

New nanocomposite materials based on polymerization of [oligo(oxyethylene) methacrylates] in the presence of montmorillonite clay

Intercalation of poly[oligo(oxyethylene) methacrylates] onto sodium montmorillonite (MMT) clay has been investigated. A polymer–clay hybrid has been synthesized through intercalation of the monomer followed by its solution free‐radical polymerization. Eight polymer–clay hybrids were prepared using different weight ratios of clay, different oligo(oxyethylene) lengths and different proportions of crosslinker. Evidence of the development of nanostructures is obtained from scanning electron microscopy, and wide‐angle X‐ray diffraction studies support these results which show disappearance of the peak characteristic to d₀₀₁ spacing. In this hybrid MMT is dispersed homogeneously in the polymer matrix. © 2003 Society of Chemical Industry     

采用多模复合导引头提高反舰导弹突防能力

分析了现有反舰导弹制导体制的特点，提出了反舰导弹如采用被动微波／红外成像双模复合导引头，将是提高其突防能力的有力举措，同时提出了研制主被动／红外成像三模复合导引头的建议，并给出了三模导引头结构布局示意图。