Superplastic behaviour of Ti-48at.%Al two-phase titanium aluminide compacts made from mechanically alloyed powder

An HIP compact of MA-processed powder having a nominal composition of Ti-48at.% Al was produced. The compact consisted of a large amount of TiAl(λ) and a small amount of Ti₃Al (₂), in a completely ultra-fine equiaxed grain structure. This two-phase compact showed typical superplastic deformation behaviour. A maximum elongation of 550% was obtained. A strain exponent, n = 2, and grain size exponent, p = 2, were determined from the results of a strain-rate-change test and a creep test at constant initial stress using samples having various grain sizes, respectively. The activation energy for creep, Q_c at constant stress was calculated to be 350 kJ/mole. It is concluded that the superplastic deformation mechanism of the material under study is grain boundary sliding controlled by lattice diffusion in the TiAl phase.     

Microstructural Effects of Ion Implantation on Molybdenum

The effects of ion implantation and subsequent annealing on the microstructure of molybdenum have been investigated by transmission electron microscopy. The ions investigated were carbon, nitrogen, and tellurium. The ion-induced damage was found to give rise to grain boundary migration phenomena both during implantation and during subsequent annealing. Precipitation or ordering was found to occur for each ion on annealing.     

正交曲线坐标下三维代数应力通量模型

针对弯曲及不规则明渠的水动力及物质输运特性，本文建立了曲线坐标系下的三维代数应力通量数学模型，对平面上弯曲及不规则复杂边界情形，采用Poisson方程进行正交曲线坐标变换，各向异性的湍流代数应力通量模型被引用于本文的模拟计算中，以体现复杂边界条件引起的水动力及物质输运特性的变化。通过180度强弯曲明渠水槽及贵溪电厂不规则边界河段物理模型试验两个实例计算表明，实测值与计算吻合良好，效果令人满意。     

A review of error estimation and adaptivity in the boundary element method

When using the boundary element method, the accuracy of the numerical solution depends critically on the discretization of the boundary into elements (panels). The distribution of the panels is one of the most important decisions taken when analyzing a problem, but still the vast majority of users employ empirical guidelines to distribute the panels. This paper reviews the various adaptive schemes that have been proposed for boundary elements. Numerical results are obtained for infinite fluid flow problems and free surface problems and are used to assess the reliability and effectiveness of each method.     

改进的FD—TD法分析二维理想导体TM近区散射问题

本文针对一般ＦＤ－ＴＤ方法分析计算二维理想导体散射问题所遇到散射体边角处难以精确处理的缺点进行了改进。将边角处总场近似解析解直接引入ＦＤ－ＴＤ法差分公式，得到了有关修正系数，为了检验此方法的有效性，有无限长导体方柱为例分别用一般ＦＤ－ＴＤ法和本文的ＦＤ－ＴＤ方法进行了分析研究，并与ＭＯＭ法进行了比较，所得结果说明改进后的ＦＤ－ＴＤ方法对分析计算导体边角附近电流分布特性是较有效的。     

溢流反弧段水流边界层有关概念的探讨

本文对溢流反孤段水流边界层的定义方法进行分析讨论。在分析及弧段流速分布的基础上提出离心力附加边界层厚度和粗糙度附加边界层厚度的概念,研究了壁面曲率和壁面粗糙度对溢流反弧段边界层发展的影响。     

一种网格结构的雷达信号处理单元

介绍了一种采用网络结构，使用五片SHARC芯片组成的相控阵雷达信号处理单元。并介绍了此单元上基于IEEE1149.1边界扫描标准的故障诊断系统。     

Estimation of true dihedral angles and relative grain boundary energies in polycrystals using the disector

Relative grain boundary energies can be simply related to true dihedral angles, which are the angles between grain boundary planes meeting at triple edges in polycrystals. Some limited efforts in the measurement of true dihedral angles have used the technique of serial sectioning, which is usually cumbersome and time consuming. In this study the three‐dimensional probe called the ‘disector’ has been employed to evaluate true dihedral angles. This probe, combined with automated image processing, introduces precision as well as efficiency, overcomes the disadvantages of the two‐dimensional probe and is far less tedious and less complicated than serial sectioning. It is shown that the technique is relatively simple and therefore can be applied to obtain a significantly large and accurate statistical sample of true dihedral angles. The application of this method is demonstrated by evaluating the triple junction geometry and the associated relative grain boundary energies in polycrystalline 316L austenitic stainless steel.