Prediction of the energy dissipation rate in ductile crack propagation

In this paper, energy dissipation rate D vs. Δa curves in ductile fracture are predicted using a ‘conversion’ between loads, load‐point displacements and crack lengths predicted by NLEFM and those found in real ELPL propagation. The NLEFM/ELPL link was recently discovered for the DCB testpiece, and we believe it applies to other cracked geometries. The predictions for D agree with experimental results. The model permits a crack tip toughness R(Δa) which rises from J_c and saturates out when (if) steady state propagation is reached after a transient stage in which all tunnelling, crack tip necking and shear lip formation is established. J_R is always greater than the crack tip R(Δa) and continues to rise even after R(Δa) levels off. The analysis is capable of predicting the usual D vs. Δa curves in the literature which have high initial values and fall monotonically to a plateau at large Δa. It also predicts that D curves for CCT testpieces should be higher than those for SENB/CT, as found in practice. The possibility that D curves at some intermediate Δa may dip to a minimum below the levelled‐off value at large Δa is predicted and confirmed by experiment. Recently reported D curves that have smaller initial D than the D‐values after extensive propagation can also be predicted. The testpiece geometry and crack tip R(Δa) conditions required to produce these different‐shaped D vs. Δa curves are established and confirmed by comparison with experiment. The energy dissipation rate D vs. Δa is not a transferable property as it depends on geometry. The material characteristic R(Δa) may be the ‘transferable property’ for scaling problems in ELPL fracture. How it can be deduced from D vs. Δa curves (and by implication, J_R vs. Δa curves) is established.     

集团变分法(CVM)及其在合金相图计算中的应用

介绍了集团变分法的集团概率变量、配置熵等统计分析的理论基础及Helmholtz自由能的描述模型.提出了巨势及相对化学势的几何分析理论.讨论了应用集团变分法和巨势分析理论进行相平衡计算的过程,并分析了同结构平衡相图计算的若干实例.     

Improvement in Stress Corrosion Crack Growth Resistance of an Austempered Cast Steel by a Novel Two-Step Austempering Process

An investigation was carried out to examine the influence of microstructure on the stress corrosion cracking (SCC) growth behavior of an austempered high-carbon (1.00%), high-silicon (3.00%), and high-manganese (2.00%) cast steel. Compact tension specimens were prepared from this cast steel as per American Society for Testing Materials standard E-399 and were given four different heat treatments to produce different microstructures. The SCC behavior of these specimens was studied in 3.5% NaCl solution. The test results indicate the K_ISCCvalue of the material increases as the austenite content increases. Significant improvement in SCC resistance was achieved by using a novel two-step austempering process. Intergranular crack growth was observed in all these specimens.     

阜新市细河改造工程坝基渗漏计算及处理效果分析

阜新市细河改造工程由四座橡胶坝和两岸防洪大堤组成，由于堤(坝)基第四系冲洪积层广泛发育，存在渗漏同题。合理选择施工处理方案，是工程成功的关键。作者根据场区不同的地质条件环境条件采取有针对性的不同处理方案，既解决了防渗问题又缩短了施工工期，降低工程造价，取得了很好的经济效益和社会效益。     

乙烯装置失效模式分析及基于风险的检验

简述了乙烯装置的工艺流程,分析了装置中常见的几种失效模式及其分布;以乙烯裂解装置为例,简述了RBI的执行过程和结果,从基于风险的检验理念,对制订设备检验策略提出了几点建议。     

乙烯裂解炉辐射炉管施工技术

乙烯裂解炉辐射炉管的施工比较复杂,文章结合吉林石化分公司15万t／a乙烯装置节能改造项目的施工实践,介绍了辐射盘管系统施工的准备工作、辐射盘管组装顺序、集管箱开孔及组焊、猪尾管预制安装、辐射盘管吊装等方面的施工经验。     

建(构)筑物机械拆除方法综述

介绍了几种常用的建(构)筑物机械拆除方法,对其工作原理、特点、应用条件及局限性加以分析和说明。     

穿壁焊极柱合金探索

本文对起动用铅酸蓄电池穿壁焊极柱用合金配方进行了探索 ,并得到了良好的应用效果     

利用Excel表格进行供暖系统计算

利用Excel表格进行供暖工程设计计算，可以减少工作量，提高工作效率。介绍了房间热负荷和供暖管道水力计算方法。     

催化裂化干气回收乙烯用于制备环氧乙烷的研究

叙述了在YS型银催化剂作用下，利用催化裂化干气回收的乙烯制备环氧乙烷的实验研究。结果表明：在银催化剂上催化氧化生成环氧乙烷的过程中，使用回收的乙烯，催化剂的初选择性可达80％；在保持环氧乙烷时空产率不变，经过2000h催化剂稳定性试验后，选择性下降了3—4个百分点，反应温度上升约10℃，与用聚合级乙烯为原料进行比较，催化剂初选择性低2—3个百分点、稳定性略差。该结果为用回收乙烯生产环氧乙烷提供了试验依据。