疲劳/蠕变复合作用下聚苯乙烯的交互损伤研究

探讨了在疲劳／蠕变复合作用下聚苯乙烯的损伤交互作用，结果表明，在疲劳／蠕变复合作用下聚苯乙烯存在疲劳和蠕变的交互损伤，其断裂寿命比纯疲劳或纯蠕变的断裂寿命低；断裂机制是疲劳循环载荷松动和活化了分子链或链段，从而促进蠕变运动和断裂，并且，疲劳／蠕变的交互损伤程度与温度密切相关。     

山西引黄工程南干线7# 隧洞衬砌外水压力研究

本文采用综合修正系数取代规范建议的单一折减系数,用渗流场分析方法确定作用在引黄入晋南干线7#隧洞衬砌上的外水压力。由己知钻孔水位及泉水位反演出各地层的渗透张量及地表入渗强度求得初始渗流场。衬砌外水压力分析中考虑了衬砌混凝土的渗透性以及排水、灌浆等工程措施的影响。根据分析结果,提出了系统排水孔布置的建议,得出了在相应的排水减压措施下衬砌厚度由原设计35cm减至25cm,这一建议已被采用,取得了巨大经济效益。     

COPART:一种面向约束条件的自适应软硬件划分算法

本文介绍一种将自适应算法、遗传算法和列表调度算法结合起来应用于软硬件划分问题的算法COPARTART，并提出了一种基于约束条件的开销系数自适应调整方法，该方法所获得的划分结果能够良好体现设计目标。     

An inverse solution methodology for estimating the diffusion coefficient of gases in Athabasca bitumen from pressure-decay data

An inverse solution methodology is developed for the estimation of diffusion coefficient of gases in highly viscous, oil-sands bitumens from isothermal, pressure-decay measurements. The approach involves modeling the rate of change in pressure using the diffusion equation for the liquid phase coupled with a mass balance equation for the gas phase. The inverse solution framework is utilized to arrive at two graphical techniques for estimating the diffusion coefficient. Both techniques involve the determination of the slope of a straight line resulting from plotting the experimental data in accordance with the developed model. An advantage of the proposed techniques is that the diffusion coefficient is estimated directly, i.e. without making it an adjustable parameter. The novelty of the proposed method is in its simplicity as well as its ability to isolate portions of the pressure-decay data affected by experimental fluctuations. The effect of the initial pressure on the predicted diffusion coefficient and pressure-decay profile was also investigated. The diffusion coefficients of CO₂, CH₄, C₂H₆ and N₂ in Athabasca bitumen at 50–90 °C and about 8 MPa were estimated and compared with literature values.     

Influence of aggregate content on the migration coefficient of concrete materials using electrochemical method

In order to investigate the effect of coarse aggregate content on the chloride ion migration coefficient of concrete, specimens with different coarse aggregate volume fractions and two water/cement (w/c) ratios of mortar matrix were used. The chloride ion migration coefficient of concrete is obtained using the electrochemical technique to accelerate chloride ion migration in cement-based material and the experimental results were plotted as a function of the fine aggregate volume fraction. The results are analyzed comparing experimental results and theoretical models that represent the concretes as three-phase composite materials. The three phases are the mortar matrix, the coarse aggregate, and the interfacial transition zone between the two. The chloride ion migration coefficient is used to assess the dilution, tortuosity, interfacial transition zone (ITZ) and, percolation effects of coarse aggregate in concrete. It appears that the dilution and tortuosity effects are a dominant factor affecting the chloride ion migration coefficient of concrete in the low volume fraction of coarse aggregate. As the volume fraction of coarse aggregate increases to 40 and 20% in concrete of w/c ratio 0.35 and 0.45, respectively, the ITZ with percolation effects are significantly.     

Copper(II) removal from aqueous solutions by fly ash

The removal of Cu(II) by adsorption on fly ash has been found to be concentration, pH and temperature dependent. The kinetics of adsorption indicates the process to be diffusion controlled. The Langmuir constants have been calculated at different temperatures, and the adsorption has been found to be endothermic (ΔH = 15.652 kcal mol^?1). The maximum removal is observed at pH 8.0, and variation in adsorption with pH has been explained on the basis of surface ionisation and complexation.     

EXPERIMENTAL INVESTIGATIONS ON LONGITUDINAL DISPERSION CHARACTERISTICS OF TIDAL RIVERS

1 .　ＩＮＴＲＯＤＵＣＴＩＯＮＵｎｄｅｒｔｈｅｉｎｆｌｕｅｎｃｅｏｆｎａｔｕｒａｌｔｉｄｅｓ,ｔｈｅｉｎｔｅｒａｃ ｔｉｏｎｓｂｅｔｗｅｅｎｆｌｏｗｆｅａｔｕｒｅｓａｎｄｐｏｌｌｕｔａｎｔｌｏｎｇｉｔｕｄｉｎａｌｄｉｆｆｕｓｉｏｎｉｎｔｉｄａｌｒｉｖｅｒｓａｒｅｉｍｐｏｒｔａｎｔｆｏｒｗａｔｅｒｅｎｖｉ ｒｏｎｍｅｎｔｒｅｃｔｉｆｉｃａｔｉｏｎｉｎｅｓｔｕａｒｉｎｅｒｅｇｉｏｎｓ.Ｔｈｅｄｉｆｆｕ ｓｉｏｎａｎｄｔｒａｎｓｐｏｒｔｏｆｐｏｌｌｕｔａｎｔｉｎｎａｔｕｒａｌｒｉｖｅｒｓｆａｌｌｉｎ ｔｏｍ…     

Analysis and Optimization of Noise in Bipolar RF Harmonic Mixers

A noise analysis of bipolar harmonic mixers (BHM) used for direct-conversion receivers is presented in this paper. Analytical and simulated results for the transfer function of the mixer are presented. Simple analytical expressions describing noise contribution from all sources are derived. Estimation of flicker noise quite agrees with harmonic-balance simulation results. Based on the derived expressions, total time average noise power spectral density (PSD) at the output is compared with simulation results. For the recommended regions of operation, error is less than 20%. The overall BHM noise figure (NF) is calculated and optimized based on a simple extracted formula. Errors introduced by analysis remain within a 1.5-dB margin with respect to simulation results. The validity of analysis for high frequencies is justified. The effect of flicker noise coefficient on the overall mixer NF is compared for different available processes.     

横泉水库旧坝体及黄土台地强夯处理实践

山西省横泉水库在原有遗留工程基础上进行重新建设，以往的4次施工，填兢了长400m、高17m左右的左岸坝体，填土约120万m^3，但坝体填筑质量极差，干客重和渗透系数根本无法满足设计要求。此次重新建设，决定对这部分干客重不迭设计要求且具有湿陷性的左岸旧坝体以及左岸黄土台地进行强夯处理，对坝体进行强夯处理在省内还是首次进行，在国内也比较少见，通过处理，坝体质量达到了设计要求，并且节约了投资，效果明显。     

Crystallization and thermoelectric behavior of conductive-filler-filled poly(ε-caprolactone)/poly(vinyl butyral)/montmorillonite nanocomposites

Crystallization and thermoelectric properties of poly(ε-caprolactone) (PCL)/poly(vinyl butyral) (PVB)/montmorillonite (MMT) nanocomposites containing carbon black (CB) have been studied as a functions of a small amount of amorphous PVB content and a wide range of molecular weight of PVB. X-ray diffraction data of PCL/PVB/MMT nanocomposites indicates most of the swellable silicate layers are exfoliated and randomly dispersed into PCL/PVB system. The band spacings of PCL spherulites in PCL/PVB/MMT nanocomposites decrease with increasing PVB content, and this indicates that increasing the PVB content greatly shortens the period of lamellar twisting. The presence of 1 wt% MMT and higher molecular weight of PVB also shorten the period of PCL lamellar twisting. Nucleation and crystallization parameters, such as growth rate G and Avrami exponent n, can be determined by using POM and DSC isothermally crystallized at 41 °C. For samples with the same CB content, the intensity of positive temperature coefficient (PTC) (I_PTC, defined as the ratio of peak resistivity to resistivity at room temperature) of the nanocomposites was increased as the content and the molecular weight of PVB increases. The change of the PTC property related to the morphological difference (i.e. period of lamellar twisting) in the nanocomposites can be discussed.