Monte-carlo modeling of grain growth in Zr equal channel angular pressed and recrystallized

Grain boundary character distribution in equal-channel-angular pressed Zr was studied. Using a die design of 90°/20° and an operation temperature of 350°C. The initial grain size of 20 μm was reduced to about 270 nm with 4 passes via route B_c. The grain growth kinetics of the recrystallized state was obtained by experiment and Monte-Carlo computer simulation, respectively, which showed good agreement. Based on kinetics and morphological characteristics, it was concluded that the grain coarsening mechanism was governed by normal grain growth. No sign of abnormal grain growth was detected either in the experiment or in simulation despite taking into consideration anisotropy in grain boundary energy as well as its mobility. This indicates that grain boundaries produced by severely deformed Zr are stable against explosive coarsening. The evolution characteristics of the microstructure in the present ECA pressed and recrystallized Zr differed from those of cold rolled Ti in that the grain boundary misorientation distribution and texture were rather stable during grain growth. Jointly Appointed by the Center for Advanced Aerospace Materials This article is based on a presentation made in the 2002 Korea-US symposium on the “Phase Transformations of Nano-Materials,” organized as a special program of the 2002 Annual Meeting of the Korean Institute of Metals and Materials, held at Yonsei University, Seoul, Korea on October 25–26, 2002.     

热压变形对灰口铸铁石墨形态的影响

研究了灰口铸铁(HTl50)在900℃大压下量塑性变形后石墨的分布形态，结果表明：随着压下量的增加，石墨片逐渐趋于平行分布；变形过程中发生了碳的回溶，同时伴随着石墨片的断裂；石墨片体积分数及片间距随压下量的增加而逐渐减少。     

铸态AZ80镁合金高温热变形行为研究

在Gleeble-1500热模拟机上对铸态AZ80镁合金在应变速率为0.005s-1~5s-1、变形温度为200℃~400℃条件下的高温热压缩变形行为进行了研究。结果表明,材料真应力-真应变曲线呈现动态再结晶特征。在温度T≥250℃,试样流变应力行为对应变速率敏感;在低温下T=200℃,应变速率对流变应力影响不大。高温下试样流变应力符合幂指数函数关系,应力指数n为6,热变形激活能Q为220kJ/mol。在高应变速率条件下,试样在变形中的温升是应变量的函数。实验中,Zener-Hollomon参数值大的试样温升明显,而Zener-Hollomon值小的试样变形温度基本保持不变。     

弹性变形对仿人机器人步态规划的影响分析

仿人机器人行走步态研究的理论、方法及建模均未考虑系统各部件弹性变形的影响，导致行走实验结果与理论步态规划存在较大的差异，制约了步行质量的提高和连续快速稳定步行的实现。本文运用ANSYS有限元软件，针对清华大学研制的THBIP—Ⅰ型仿人机器人样机，建立精确的有限元模型，进行步行运动弹性变形及其对步态规划影响的有限元仿真分析，在此基础上提出了对步态规划进行局部修正完善的方法，步行实验证明该有限元模型及仿真分析结果是有效的。     

延缓与加速A1-Cu合金时效析出反应的研究

研究了溶质原子浓度、Si晶体第二相、残余形变、外加莫来石(Mullite)短纤维及其交互作用，对二元Al—Cu合金时效析出行为的影响。试验材料采用挤压铸造方法制备，复合材料中纤维体积分数为18％。实验结果表明：随溶质原子浓度的升高，A1-Cu二元合金中GP，θ″和θ′相的析出都得到了相应加快；Si含量超过一定值后，随Si含量增加，A1-Cu-Si合金中GP区形成受到抑制，而θ″和θ′相的析出得到加快；形变对GP区的抑制和对θ″，θ′和θ相的加速析出具有十分明显的作用；纤维本身除对GP区抑制和对θ″，θ′相的析出加速外，还会与溶质原子、合金元素或第二相以及残余形变交互作用，使GP区被抑制，而θ″，θ′甚至θ相被加速析出等现象进一步加强。用位错理论能较好地解释析出反应延缓与加速的微观机理。     

形变与热处理对Cu-Cr合金力学性能的影响

研究了不同形变与热处理工艺对多元Cu-Cr合金的力学性能的影响.结果表明该合金有显著的时效强化特性,强化相为Cr,当合金经65%变形再经500℃×4 h时效处理可获得较高的硬度;变形能降低合金的冲击韧度,而时效处理对合金的冲击韧度影响不大.     

STRAIN INDUCED STRUCTURAL TRANSITION OF INTERFACES AND TWINS IN A HOT－DEFORMED DUAL－PHASE TIAL ALLOY

ＳＴＲＡＩＮＩＮＤＵＣＥＤＳＴＲＵＣＴＵＲＡＬＴＲＡＮＳＩＴＩＯＮＯＦＩＮＴＥＲＦＡＣＥＳＡＮＤＴＷＩＮＳＩＮＡＨＯＴ－ＤＥＦＯＲＭＥＤＤＵＡＬ－ＰＨＡＳＥＴＩＡＬＡＬＬＯＹＣＨＥＮＧｕｏＦｉａｎｇ；ＷＡＮＧＪｉｎｇｕｏ；ＺＨＡＮＧＬｉｃｈｕｎａｎｄ...     

轴类零件校直工艺广义预测多步算法研究

本文基于行程控制的轴类零件校直工艺公式 ,构建了模拟轴类零件校直工艺过程的广义预测控制模型 ,应用广义预测算法 ,实现了对轴类零件弹塑性非线性残余变形的均匀控制 ,实验研究表明 ,该方法能满足精密校直要求 ,并且随着控制步长的增多 ,控制效果显著。     

Effects of Austempering after Hot Deformation on the Mechanical Properties of Hot Rolled Si-Mn TRIP Steel Sheets

Excellent mechanical properties are obtained by austempering after hot deformation without subsequent heat treatment in the present Si-Mn TRIP steel sheets. Isothermal holding time after finishing rolling has affected the mechanical properties of this steel. The results show that the sample exhibits a good combination of ultimate tensile strength and total elongation when it is held at the bainite transformation temperature after hot deformation. The stability of retained austenite increases with an increase of isothermal holding time, and a further increase in the holding duration results in a decrease of it. The tensile strength, total elongation and strength ductility reach the maximum values (774MPa, 33% and 25542MPa% respectively) for this sort of hot rolled Si-Mn TRIP steel using the optimal technology.     

钒氮微合金化热轧带肋钢筋径向组织分布特征

通过用金相、扫描电镜等方法观察得出,钒氮微合金化热轧带肋钢筋肋部主要由细小的铁素体晶粒、片层较细的珠光体和少量离异珠光体组成;其基体组织是沿钢筋纵向呈明显条带状分布的铁素体和珠光体。同时,定量测量了铁素体条带密度、铁素体晶粒尺寸、珠光体体积分数及其片层间距沿径向的分布情况,并分析了铁素体晶粒尺寸和珠光体体积分数在芯部反常分布的原因。