Temperature effects on the mass flow rate in the SBI and similar heat‐release rate test equipment

In various medium‐to‐large‐scale fire test equipments like the ISO room corner test (RC), and more recently, the single burning item test (SBI) the mass flow rate measurement of the combustion gases plays a key role in the determination of the heat‐release rate and smoke‐production rate. With the knowledge of the velocity profile and the temperature of the flow, the mass flow rate is obtained by measuring the velocity on the axis of the duct. This is done by means of a bi‐directional probe based on the pitot principle. However, due to the variation of the mean temperature and the temperature gradient in any cross section of the duct, introduced by ever changing combustion gas temperatures, the velocity nor the density profile are constant in time. This paper examines the resulting uncertainty on the mass flow rate. Copyright © 2006 John Wiley & Sons, Ltd.     

Delamination Analysis for Laminated Composites. II: Numerical Verification

A validation of the delamination analysis models developed in a companion paper is provided through comparisons of predictions with finite‐element and elasticity solutions. The models are applied to the analysis of composite compression specimens reinforced with end tabs. An elasticity solution for the gage section of the specimens is developed. A comparison of the characteristic roots shows that the predictions of the models include the material and geometric parameters that control the behavior, and the roots corresponding to the basic stretching and bending modes are accurately predicted. The stress distribution at the interface between tabs and specimen is in good agreement with a finite‐element simulation. The interlaminar shear and peel stresses show an exponential increase with a maximum intensity at the free edges of the tabs. The behavior of previously tested specimens is explained; and practical guidelines for specimen design are provided to avoid unwanted extraneous modes of failure. The influence of the deformation modes associated with each model is investigated. An assessment of the accuracy and level of complexity is presented.     

THE STICKY ISSUES OF DRYING

Unconrolled agglomeration of particles and adhesion of the particulate mass to wall surfaces are common severe problems in many drying operations. This paper reviews the mechanisms of interparticle and particle-surface attraction as well as the theory and the existing tests for characterising powders in terms of internal strength, wall friction and adhesion. The usefulness of the information obtained from these tests in dryer design and operation is critically reviewed. The importance of powder stickiness in various types of dryers is discussed and established methods of combating the problem are presented Recommendations an made for further research in the area of powder cohesion and adhesion.     

Finite element simulation of the mechanics of flat contact pad fretting fatigue tests

An understanding into the macro kinetic and kinematic behaviour of fretted surfaces is provided. Making use of a modified version of a previously developed in‐house two‐dimensional elastic–plastic finite element analysis numerically simulates flat contact pad fretting fatigue tests. Basic macro mechanics concepts are adopted to idealise two bodies with rough contact surfaces and loaded at two different sites with arbitrary axial loading profiles. A time scale factor is devised to recognise the earliest candidate out of the events possibly accommodated at each loading increment. The present analysis utilises a relevant experimental set up developed in the Structural Integrity Research Institute of the University of Sheffield as an application. Computational results accurate to within 1.2% and corresponding to one contact pad span and six constant normal loads acting individually with four amplitudes of two sinusoidal axial load cycles are presented. The present computations include (1) the development of the global and local normal and tangential reactions and relative sliding displacement acting along the fretting surfaces and (2) contact pad deformation, generated stress fields and plasticity development within the neighbouring region of the fretted area.     

Laboratory Evaluation of Smear Zone and Correlation between Permeability and Moisture Content

In this study, the extent of the smear zone and the reduction of permeability and water content within the smear zone were investigated using a large-scale consolidometer. The installation of vertical drains by means of a mandrel causes significant disturbance of the subsoil surrounding the mandrel, resulting in a smear zone. The extent of the smear zone for Moruya clay (New South Wales, Australia) was estimated on the basis of normalized permeability and the reduction of water content by taking undisturbed samples (horizontally and vertically) at different locations. This study reveals that a significant reduction in water content and horizontal permeability takes place towards the drain, whereas the variation in the vertical permeability is negligible. The smear zone for Moruya clay was found to be 2.5 times the equivalent radius of the mandrel with the horizontal permeability varying from 1.09 to 1.64, an average of 1.34 times smaller than that of the undisturbed zone. Finally, a correlation between the permeability decrease and water content reduction within smear zone is proposed.     

Predicting N mineralized in a Georgia Coastal Plain field

The N mineralized from soil organic matter provides an important portion of N available for crop production. The objective of this study was to determine the amount of spatial variability in N mineralization potential in a field and to evaluate three different methods that might be used to estimate this variability. The three methods tested included predicting the N mineralized from surface soil properties as well as from a biological and a chemical procedure. Three soils varying in N mineralization potential were selected for the study from a field in the Georgia Coastal Plain. The N mineralized from these soils was determined by an N balance of unfertilized and cropped plots. The amount of N mineralized could not be reliably predicted from surface soil organic C, although surface soil clay concentration was positively correlated with the N mineralized. The N mineralized that was predicted using mineralization parameters determined by aerobic incubation, adjusted daily for soil water content and temperature, was approximately 50% of the field measurements of N mineralized. The values of NH₄-N extracted with hot 2 M KCl were related significantly to N mineralized in the field (r²= 0.60) and also to the zero order rate constant of mineralization, k₀ (r²= 0.77), determined from the N mineralized in the aerobic laboratory incubation.     

Processing study of a high temperature adhesive

An adhesive-bonding process cycle study was performed for a polyimidesulphone. The high molecular weight, linear aromatic system possesses properties which make it attractive as a processable, low-cost material for elevated temperature applications. The results of a study to better understand the parameters that affect the adhesive properties of the polymer for titanium alloy adherends are presented. These include the tape preparation, the use of a primer and press and simulated autoclave processing conditions. The polymer was characterized using Fourier transform infrared spectroscopy, glass transition temperature determination, flow measurements, and weight loss measurements. The lap shear strength of the adhesive was used to evaluate the effects of the bonding process variations.     

TBC experience in land- based gas turbines

This paper summarizes prior and on-going machine evaluations of thermal barrier coatings (TBC) for power generation, that is large industrial gas turbine applications. Rainbow testing of TBCs on turbine nozzles, shrouds, and buckets are described along with a test of combustor liners. General Electric Power Generation has conducted more than IS machine tests on TBC turbine nozzles with various coatings. TBC performance has been quite good, and additional testing, including TBCs on shrouds and buckets, is continuing. Included is a brief comparison of TBC requirements for power generation and aircraft turbines.