Crystallization and Drying in Thin Sucrose Films During Panning

Sucrose crystallization in thin films (50–55 μm) was studied, using a videomicroscopy technique, at conditions encountered during hard panning processes. No nucleation occurred in unseeded films, while a linear increase in seeded crystals occurred during drying. Crystal growth rate increased with temperature (25–30°C) and with air velocity (2.4–12.5 m/sec), but did not change with varying sucrose concentrations (70–76% w/w) and relative humidities (0–66% at 30°C). FD & C Yellow No. 5 food coloring in the dye form (0.05–0.5 g/100 mL) showed no effects while similar concentrations in the lake form inhibited crystal growth rate.     

微量Ag对CP276合金性能和组织的影响

研究添加不同含量的Ａｇ对ＣＰ２７６合金的拉伸性能和时效组织的影响。对拉伸强度、延伸率测试及透射电镜观察表明：０．１１ｗｔ％加入可促进Ｔ１相析出，使合金强度值升高；０．３５ｗｔ％Ａｇ的加入可在时效前期生成富Ａｇ、Ｍｇ的稳定的ＧＰ区，从而降低合金中Ｃｕ的固溶度，阻碍Ｔ１相析出，时效后期，ＧＰ区分解，生成大量Ｔ１相，使合金强度值显著升高。     

A Model for Through Drying of Tissue Paper at Constant Pressure Drop and High Drying Intensity

A mathematical model for through drying of paper at constant pressure drop was developed. The model is based on physical properties; hence, basis weight, pressure drop, drying air temperature, pore size distribution, initial gas fraction, and tortuosity are important input parameters to the model. The model was solved for different combinations of the variables basis weight, drying air temperature, and pressure drop corresponding to industrial conditions and the results were compared with data from bench-scale experiments. The simulations show that the drying rate curve is very sensitive to the air flow rate and that correctly modeling the correlation between pressure drop and air flow rate is the most important factor for a successful model for through drying. The model was tuned by adjusting the parameters initial gas fraction and tortuosity in order to give the best possible fit to experimental data. For a given basis weight and pressure drop, different drying air temperatures resulted in relatively constant values of the fitted parameters. This means that the model can well predict the effects of changes in drying air temperature based on a tuning of the model performed at the same basis weight and pressure drop. However, for a given basis weight, an increase in pressure drop yielded fitted parameters that were somewhat different; i.e., a lower initial gas fraction and a higher tortuosity, a change that increases the resistance to air flow. This implies that the correlation between pressure drop and air flow rate in the model does not quite capture the nonlinear relationship shown by the experiments.     

浅谈水泥基渗透结晶型防水材料标准及性能指标

针对GB18445-2001《水泥基渗透结晶型防水材料》标准在使用过程中发现的一些问题，对标准中的部分性能指标的确定及试验方法提出修改意见。     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

纳米NiO粉体的制备及其表征

采用溶胶转化－凝胶法制备了纳米级NiO粉体。Ni(OH)2粉体的TG－DSC分析表明：在升温速率为10℃/min的条件下，粉体在489K时开始显著分解，626K时分解完毕。X－射线衍射分析表明：分解产物为纯净的NiO2。NiO粉体的化学成分分析表明：其纯度高于国家标准。TEM电镜分析表明：NiO粉体呈单分散的球形或棒状颗粒。对NiO粉体的热敏性能有待进一步研究。     

Effect of the Treatment Temperature on the Surface Drying Set of Sugi Boxed-Heart Square Timber

High-temperature and controlled humidity treatment before drying has proven to be highly effective in preventing surface checks by forming drying sets in the surface layer of boxed-heart square timber in Japan. In this study, we examined the differences of the surface drying sets on sugi timber under different treatment temperatures. As a result, the width of a surface check after drying was much smaller at a treatment temperature of 120°C than at 80°C, and this indicates that the drying set with 120°C treatment would be larger than that with 80°C treatment. Also we observed that treatment temperature had a greater effect on the drying set as the drying advanced.     

微波干燥原理及其应用

介绍了微波干燥的原理和主要特点及其应用的现状,并且给出了微波干燥经济核算的计算方法。     

传媒产品生产的外在性

因为价格机制不能正常运行和不能正常发挥作用,或者因为社会经济活动的相关性,传媒产品的生产出现外在性现象,社会成本问题不可避免.选择合适的产权制度安排,不仅能够消除传媒产品生产的外在性,而且有利于传媒资源的有效利用和传媒经济的不断发展.     

化学成分和固溶温度对1Cr17Mn9Ni4N不锈钢组织和性能的影响

为提高1Crl7Mn9Ni4N钢固溶处理后的力学性能(特别是钢的强度)，研究了化学成分及固溶处理温度对其组织和性能的影响。结果表明，1000—1125℃固溶处理后，该钢的组织为单相奥氏体。在标准成分范围内，随着镍、锰含量的增加，该钢的强度降低，塑性有所改善。氮明显提高该钢的强度。根据试验结果，每增加0．01％的氮钢的室温强度可提高大约5MPa，且塑性基本上不受影响。当合金成分(质量分数，％)控制在C0．08—0．12、Crl6．5—17．5、Ni3．5—4．2、Mn8．0—9．0、N0．22—0．28时，1Crl7Mn9Ni4N钢经1050—1100℃固溶处理后强度较高、塑性好，室温强度σ0．2和σb可分别达到400MPa和800MPa。