提高高铬白口铸铁磨球冲击抗力的技术关键

当高铬白口铸铁含铬量为18%～28%,Cr/C值是8￣9,铸铁的显微组织是回火马氏体 少量残余奥氏体(<5%) M7C3碳化物,则磨球具有高的冲击韧性和断裂韧性K1C,具有高的冲击抗力,表现出低的冲击剥落量。     

Antimicrobial protection of cotton and cotton/polyester fabrics by radiation and thermal treatments. I. Effect of ZnO formulation on the mechanical and dyeing properties

Cotton and cotton/polyester fabrics were treated against microbial attack by applying a formulation based essentially on ZnO under high‐energy radiation and thermal curing. To achieve the homogeneity and the reactivity of the treating formulation, a binder (Impron MTP) and a dispersing agent (Setamol WS) were used with ZnO. The antimicrobial property of the fabrics was evaluated, in terms of mechanical properties, by a soil burial test. Moreover, the effect of antimicrobial finishing on the dyeing properties in terms of color strength was investigated. It was found that the best composition that affords the best antimicrobial protection to cotton fabrics contains 2% ZnO, 2% binder, and 1% dispersing agents. For the cotton/polyester blend, the best results were achieved at the same conditions except the ZnO was 1%. It was found that the treatment under the effect of electron‐beam irradiation is better than that of gamma irradiation and thermal curing. The results showed that when the finishing process was carried out before dyeing with a reactive dye, it affects the color strength rather than performing the finishing after the dyeing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1129–1137, 2003     

利用C++Builder对处理ESCR数据方法的改进

介绍一种利用C＋＋Builder编程工具自动处理聚乙烯环境应力开裂(ESCR)试验数据的方法。此方法利用计算机简化试验数据的处理过程,消除标准试验方法中作图法所引入的人为误差,并可以大幅度缩短试验时间。     

成形压力对氧化铝瓷球性能的影响

本文以不同的压力等静压成形瓷球，研究了成形压力对瓷球烧结温度、密度及耐磨性的影响。结果表明：在本研究系统内随着压力的增加瓷球的烧结温度下降，烧成温度范围拓宽。采用150MPa成形的瓷球密度最大且耐磨性最好。     

半刚性钢-混凝土组合节点受弯承载力的计算

在半刚性钢 -混凝土组合框架中 ,混凝土板中的纵向钢筋增加了节点的强度和刚度 ,但是 ,传统的设计方法往往忽略纵向钢筋的作用而采用简化的计算模型。因此 ,出于经济效益考虑 ,应该根据半刚性组合节点的实际受力性能建立更加准确的计算方法。这里详细介绍了考虑混凝土板纵向钢筋作用的半刚性组合节点受弯承载力的计算方法 ,计算结果表明 ,建议的公式与试验结果吻合良好 ,可供规范制定和工程应用参考。     

高柔韧性聚氨酯丙烯酸酯的合成及应用

选用不同结构的多元醇作骨架，合成一系列高性能的聚氨酯丙烯酸树脂，并通过对聚氨酯丙烯酸树脂性能的对比研究，发现以聚丁二烯二元醇为骨架的聚氨酯丙烯酸酯树脂具有极佳的柔韧性和优异的低温耐曲折性。     

Alkaline fuel cells: contemporary advancement and limitations

ZeTek Power recently introduced mass manufacturable and cost effective alkaline fuel cells on the market. Today's research is focused on further improvement both in terms of performance increase and cost reduction. This research is classically performed using small (4 cm²) experimental electrodes in the half-cell configuration. This allows the primary electrochemical losses in an anode or cathode to be determined independently. Additional performance losses occur when one integrates large electrodes into a module of 24 cells and in a stack comprised of many modules. By comparing the performance of half-cell experiments to that of modules, these losses can be distinguished and addressed. The information thus obtained, both for the small electrodes and in up-scaling is vital if one is to identify the key areas in which improvement is possible and where to focus future research. Furthermore, the identification of the losses in a module and system allows us to predict the final performance from half-cell measurements of a new laboratory scale experimental electrode.     

Detoxification of cereal plant allelochemicals by aphids: Activity and molecular weights of glutathioneS-transferase in three species of cereal aphids

The activity and molecular weights of glutathioneS-transferase were studied in three species of cereal aphid:Metopolophium dirhodum, Sitobion avenae, andRhopalosiphum padi. The highest level of glutathioneS-transferase activity was recorded in extracts fromM. dirhodum and the lowest fromS. avenae, and extracts of larvae were more active than those from adults. The activity of this enzyme was higher in extracts ofS. avenae andR. padi previously fed on a moderately resistant wheat variety than on a susceptible variety. Gel filtration followed by SDS-PAGE revealed three protein bands in the active fractions. The first had a molecular weight of 28,500 and the second of 27,500 and were present in all three species of aphid. The third protein differed in the three species, having a molecular weight of 26,000 inS. avenae, 25,500 inM. dirhodum, and 24,000 inR. padi.     

热处理前后丙烯腈／溴乙烯共聚纤维的热性能和阻燃性能研究

分析了热处理前后丙烯腈／溴乙烯共聚纤维的热性能与溴乙烯含量、升温速率或热处理时间的关系，并对纤维的阻燃性与溴含量或热处理时间关系进行了研究。结果表明，溴含量的增加或热处理时间的延长对热稳定性和阻燃性的提高有较大影响，而且经热处理后纤维的阻燃性与溴无关。     

Studies of microhardness and mar resistance using a scanning probe microscope

Scanning probe microscopy (SPM) is in a period of rapid development. It shows great promise for characterizing coating surfaces. This paper describes modification of an SPM so that it can be used to mar the surfaces of coatings under controlled conditions and to characterize the mars. Mar resistance of coatings is analyzed in terms of a ‘three response, two mechanism model.' The three responses (fracture, elastic, and plastic) can be measured quantitatively using the SPM. Of the three responses, only two (fracture and plastic deformation) are marring mechanisms – elastic deformations recover instantaneously. In some cases mars resulting from plastic deformation may recover slowly with time or with immersion in water; this phenomenon is attributed to viscoelastic creep. Microhardness is also measured with the modified SPM. Some thermoset coatings appear to be substantially harder near their surfaces than in the mass of material, and such materials may respond quite differently to stress applied at different levels near the surface. This finding has important implications for all coating properties that are strongly influenced by the surface. A quantity called ‘micro mar resistance' is defined. It may be useful for comparing different coatings under specified conditions of marring. However, there can be no single quantity that expresses ‘mar resistance' of a coating under all conditions.