Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

Restoration of masonry facades, renders and final coats in a severe climate

The restoration of relatively old masonry buildings, 1870-1920, represents about 119930 flats and offices in the 4-5 largest cities in Norway. Driving rain and a severe climate are the key factors for deterioration. The paper describes a case study at the city campus of the University of Oslo.     

钨系延期药预点火反应机理研究

通过程控升温模拟点火条件，根据ＤＳＣ图谱分析，找出主要反应区的温度范围。研究结果表明，钨系延期药预点火反应是一个真正的固－固反应。     

Geochemical approach to the Bou Hadjar hydrothermal system (NE Algeria)

The Bou Hadjar low-temperature hydrothermal system is located in northeast Algeria. The four main thermal springs that are the subject of the study emerge ith temperatures between 32 and 60°C from allochthonous formations. The reservoir temperature has been estimated from chemical compositions by utilizing simultaneously the silica, gas and sulfate-water oxygen isotope geothermometers, fluid-mineral equilibrium calculations, and a mixing model. According to these thermometric methods, the most probable subsurface temperature is in the range 75–106°C. The mixing model suggests a temperature of 125°C for the parent water.     

Transport properties of 1,1-difluoroethane (R152a)

Based on reliable. carefully selected data sets. equations for the thermal conductivity and the viscosity of the refrigerant R 112a are presented. They are valid at temperatures from 240 to 440 K, pressures up to 20 MPa. and densities up to 1050 kg · m^–3. including the critical region.     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

Measurement of the thermal diffusivity of thin films on substrate by the photoacoustic method

Measurements of the thermal diffusivity of thin films on substrate have been performed by the photoacoustic method. In order to examine the method we have built a new apparatus and proposed (1) a system calibration procedure using optically and thermally thick reference samples and (2) a data analysis procedure based on the RG (Rosencwaig and Gersho) theory. As a result of using a transparent photoacoustic cell, the systematic errors which are caused by stray light have been reduced. With this apparatus, measurements have been performed on platinum, titanium, and stainless steel (SUS304) thin foils (thickness form 50 to 100 µm) with three different liquid backing materials (water, glycerol, and ethyl alcohol). The reproducibility was within ±7% regardless of film thickness and substrate materials.     

热力系统节能技术改造方案介绍

针对热电厂热力系统存在的浪费能源和设计不合理现象作了浅析 ,介绍了几种对热力系统进行改造的方案 ,并对取得的经济效益进行了计算。     

Optical measurements of thermal diffusivity of a material

The measurement of thermal diffusivity of a material (in particular, a thin film) is important for various reasons, e.g., to predict the heat transfer in the solid subjected to a thermal process, to monitor surface composition or morphology, or to detect invisible subsurface defects like delaminations. This measurement can be done in a noncontact manner using various photothermal methods. Such methods typically involve pulsed heating of the surface by small amounts using a laser source; the decay of the surface temperature after this pulsed photothermal heating is then probed to provide the thermal diffusivity. Various probing methods have been developed in the literature, including the probing of reflection, refraction, and diffraction from the pulsed heated area, infrared thermal radiometry, and surface deformation. This paper provides an overview of such techniques and some examples of their applications.     

采用荷载平衡的概念表达预应力度及在初步设计中的应用

利用荷载平衡法的概念，将预应力度用等效荷载与外荷载的比值表达，设计可利用其比值确定预应力度，便其更简捷，明确，同时，提出了预应力度的真实值问题。