Non-equilibrium particle motion in the vicinity of a single blade

The motion of sand particles close to a single moving blade was investigated using Positron Emission Particle Tracking (PEPT) during the period in which the free bed surface profile was evolving to an equilibrium shape. The area affected by the blade was divided into active and inactive regions and these were analysed separately. The characteristic heart-shape of the active region in the plan view was determined. An approximately 10-particle-diameter wide velocity transition zone is found between the two regions. While the tracer particle is in the inactive region moving away from the blade, the time dependence of the axial displacement is well described by a logarithmic relationship. The probability of particle movement towards the centre of the blade was quantified using a “central tendency” index. The calculated central tendency shows maxima at each side of the blade. The separation of the two maxima, which indicates the width of the active region, increases with fill level but is independent of rotational speed.     

光学材料的激光微加工研究进展与应用前景

综述了国内外在光学材料激光微加工方面的研究成果和应用状况，并展望了其发展前景。     

声诱饵仿真试验系统

介绍了声诱饵仿真试验系统的组成、工作原理、对接装置结构等,建立了对接装置声耦合状态下的数学模型,对近场声压分布进行了仿真计算,得出了匹配材料厚度、发射和接收换能器的选取原则。     

Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

正确选用热力管网保温材料的几个问题

介绍了做好热力管网保温应具备的有关知识和数据，以及宝钢蒸汽主干管网在采用四种保温材料下的经济保温层厚度和相对的节能效益，认为目前适于宝钢公司热源温度在６００℃以下较好的保温材料有新型矿渣棉制品和泡沫石棉板。     

泡沫夹克管的防水与保温

针对辽河油田应用泡沫夹克管道的情况，从泡沫夹克管的制作和敷设施工直到设计等环节，结合泡沫夹克管防腐保温的机理，并从理论与实践相结合角度出发，提出导致泡沫夹克管腐蚀损坏的最主要原因是管道保温层漏水，进而提出了在设计和施工过程中提高泡沫夹克管质量的措施。     

浅谈无缝钢管的壁厚偏差

通过探讨、分析无缝钢管壁厚偏差产生的原因，提出了改善钢管壁厚偏差的一些措施，并结合实际生产，得出了比较满意的结果。     

DIRECT RESONANCE OF TURBULENT BOUNDARY LAVER OVER COMPLIANT WALLS

１．　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｍａｉｎｇｏａｌｏｆｔｈｉｓｐａｐｅｒｉｓｔｏｅｘｐｌｏｒｅｔｈｅｐｏｓｓｉｂｉｌｉｔｙｔｏｌｅａｒｎｍｏｒｅａｂｏｕｔｔｈｅｍｅｃｈａｎｉｓｍｏｆｔｕｒｂｕｌｅｎｔｂｏｕｎｄａｒｙｌａｙｅｒｆｌｏｗｉｎｔｅｒａｃｔｉｏｎｓａｎｄｉｔｓｅｆｆｅｃｔｓｏｎｃｏｍｐｌｉａｎｔｗａｌｌｐｅｒｆｏｒｍａｎｃｅ．Ｔｈｅｒｅａｒｅｃｅｒｔａｉｎｐｒｅｒｅｑｕｉｓｉｔｅｃｏｎｄｉｔｉｏｎｓｔｏｆｕｒｔｈｅｒｔｈｅｓｔｕｄｙｏｎｔｈｅｍｅｃｈａｎｉｓｍ，ｉ．ｅ．ｔｈｅｃｏ…     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

绝缘涂敷制件的加工工艺研究与应用

主要论述了电工绝缘粉末的性能及其在高压电器设备应用中的有关试验项目。