重载齿轮齿面疲劳损坏及预防

点蚀和剥落是重载齿轮齿面疲劳损坏最普遍的形式.根据齿轮失效分析实例,对齿面初始点蚀、破坏性点蚀和齿面剥落等三种主要疲劳损坏的特征、发生部位及破损危害程度进行了分析研究,较系统地论述了齿轮接触疲劳破坏机理,影响因素及其产生原因,并对有关的齿面破坏提出了相应的预防措施.     

X60管线钢疲劳特性的研究

利用2、4和14mm的X60钢紧凑拉伸试样进行同样应力水平、固定应力比（R＝0．1）的疲劳裂纹扩展试验，揭示出高韧性管道钢的疲劳裂纹扩展存在显著的厚度效应。由于应力水平低，相应的离面应力也低，不足以导致分层开裂，因此，裂纹端部的三维应力约束随厚度增加而增大。4mm试样的疲劳裂纹速率远高于2mm试样，但厚度再增大，裂纹扩展速率不再有显著变化。进一步对表面裂纹试样进行疲劳裂纹扩展试验，并用勾线法纪录裂纹扩展情况，利用穿透裂纹的da/dN-ΔK曲线预测表面裂纹扩展，用2mm厚试样的数据控制裂纹表面长度的扩展，用14mm厚试样的数据控制裂纹底部沿厚度方面的扩展，得到了与表面裂纹扩展实验吻合很好的预测结果。     

储层敏感性快速预测软件在大港油田的研究与应用

在储层特征分析，室内实验，机理研究的基础上，利用人工神经BP网络建立预测模型，并编制了预测储层5种敏感性的软件，该软件受人为因素干扰小，所需参数少，准确度高，综合符合率大于80％现场应用结果表明，该技术能为制定保护油气层技术措施提供较可靠的依据，能提高油田滚动开发效益，改善老油田的开发效果，该软件对BP算法进行了改进，（1）从两方面入手使网络摆脱平坦区，一是对输入数据进行归一化处理，使O1的取值在[0,1]之间，二是一旦网络陷入平坦区域，局部极小，使连接权值Wkj,Wji和阈值Qk,Qj同时缩小一个因子，λ＞1，可使Ok(1-Ok)脱离零值，离开平坦区；（2）加速收敛，方法有自动调整学习因子，添加动量项以及对权值进行批处理，用BP算法预测储层潜在敏感性，首先应确定影响储层敏感性的主要因素，然后根据这些因素有针对性地收集有关资料并进行处理，再根据敏感性预测的要求，设计相应的网络结构进行训练，最后对训练好的网络进行.检验。     

The effect of a solid additive on rolling fatigue life

Behaviour of a series of lubricant oils and the effect of a non stoichiometric inorganic compound, as solid extreme pressure additive, on rolling fatigue life are studied using the rolling four-ball accelerated service simulation test proposed by Barwell and Scott. The results show, in all tested cases, the remarkable efficacy of this type of additive. The Total Acidity Number (tan) was found to increase with performance time for the case of the base lubricant, while for the oils with additives, it remained at its constant low value. This led to a proposal of a possible mechanism of the additive performance in the rolling process.     

Microscopic and Macroscopic Growth Rates of Fatigue Cracks in Steels and Alloys under the Influence of Crack Closure

On the basis of the experimental data, we show that the difference between the macroscopic and microscopic fatigue crack growth rates in the second section of the kinetic diagram of fatigue fracture is caused by the effect of crack closure within the limits of its existence. We establish the relationships between the macroscopic and microscopic fatigue crack growth rates and the structure of the material in the second section of the diagram for various values of the load ratio with regard for the effect of crack closure and propose a procedure of examination of the fracture processes in structural materials based on the analysis of microscopic and macroscopic fatigue crack growth rates.     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

大庆油田套损井打通道加固技术

介绍了大庆油田近几年在套损井打通道加固技术方面取得的技术进步，在磨铣打通道技术上主要对钻铣工具的结构进行了优化设计及合理及合金刀块的优选组合，提高了磨铣效率，缩短了施工周期；在爆炸打通道技术中设计了安全隔爆装置，提高了施工的安全性，使爆炸扩径技术得到完善；Φ106mm密封加固技术的研制成功，取代了Φ100mm密封加固技术，为套损井修复后的完井工艺提供有效的技术支持，提出了大庆油田目前在套损井打通道加固方面存在的难题，结合国外在套损井打通道加固方面技术的新发展，对现有技术的局限性进行了分析，提出了今后技术攻关的方向。     

Suggestions for the quantitative X-ray microanalysis of thin sections of frozen-dried and embedded biological tissues

When a microregion in a thin section of frozen-dried and embedded tissue is analysed by the conventional electron-probe X-ray continuum-normalization method, the measured quantity is in mmol of element per kg of embedded specimen. As each microregion contains an unknown amount of embedding medium, this quantity generally lies indeterminately somewhere within the wide range between mmol of element per kg of hydrated tissue and mmol of element per kg of dehydrated tissue. However, if a ‘tag’ element is incorporated in the embedding medium, the contribution of the medium to the local continuum count in each probed field should be measurable, and the X-ray data may then unambiguously yield mmol of element per kg of dehydrated tissue. This result should not be affected by shrinkage on freeze-drying or by incomplete replacement of water by embedding medium. The same X-ray data can additionally provide estimates of mmol of element per unit volume, mmol of element per kg of hydrated tissue and local dry-mass fraction. However, these estimates are subject to errors due to tissue shrinkage, incomplete replacement of water and beam damage.     

A One-Dimensional Nonlocal Damage-Plasticity Model for Ductile Materials

This paper presents a new 1-D non-local damage-plasticity deformation model for ductile materials. It uses the thermodynamic framework described in Houlsby and Puzrin (2000) and holds, nevertheless, some similarities with Lemaitre’s (1971) approach. A 1D finite element (FE) model of a bar fixed at one end and loaded in tension at the other end is introduced. This simple model demonstrates how the approach can be implemented within the finite element framework, and that it is capable of capturing both the pre-peak hardening and post-peak softening (generally responsible for models instability) due to damage-induced stiffness and strength reduction characteristic of ductile materials. It is also shown that the approach has further advantages of achieving some degree of mesh independence, and of being able to capture deformation size effects. Finally, it is illustrated how the model permits the calculation of essential work of rupture (EWR), i.e. the specific energy per unit cross-sectional area that is needed to cause tensile failure of a specimen.     

降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度破损的措施

为了降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度的破损,对气体悬浮焙烧炉焙烧过程中氧化铝粒度的影响因素进行了分析,提出了降低粒度破损的一些措施。