Performance analysis of IEEE 802.11 ad hoc networks in the presence of exposed terminals

The paper evaluates the performance effects of exposed terminals in IEEE 802.11 ad hoc networks in finite load conditions. It derives analytical models for the estimation of channel utilization and media access delay for IEEE 802.11 ad hoc networks in finite load conditions with and without exposed terminals. The simulation results show that the analytical estimated channel utilization and media access delay metrics are fairly accurate.     

利用Excel表格进行供暖系统计算

利用Excel表格进行供暖工程设计计算，可以减少工作量，提高工作效率。介绍了房间热负荷和供暖管道水力计算方法。     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Heat loss and thermoelectric generator design

With the object of evaluating its importance to thermoelectric generator design, heat loss is introduced into the standard thermoelectric generator design theory. The theory for both the constant hot and cold junction temperatures model and the constant heat input model are so modified. The modification is first order and, therefore, is limited to small leg heat-transfer coefficients. Numerical results using representative properties show that significant differences can exist between the optimum geometry and performance of a generator idealized as lossless and those of a generator designed by the modified theory. The largest differences occur with the constant heat input model.