Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

NADRA 3D information technology for analysis of processes in multicomponent soil media

This paper considers the principles of algorithmic and software implementation of the software system NADRA 3D designed to analyze processes in three-dimensional multicomponent soil media. The principles of operation of NADRA 3D are described. __________ Translated from Kibernetika i Sistemnyi Analiz, No. 6, pp. 157–174, November–December 2006.     

无油润滑压缩机活塞环和支承环设计

通过对填充聚四氟乙烯材料活塞环及带卸荷槽结构支承环的研究 ,确定了活塞及活塞环结构 ,建立了带卸荷槽支承环的力学分析模型 ,并将其结果用于结构尺寸的确定。在压缩机工艺指标不变的情况下 ,用该方法设计的活塞环和支承环性能优良。     

新疆伊犁托海水电站拱坝坝体变形监测分析

根据托海拱坝5号坝段、7号坝段例垂线实测资料分析，说明了新疆寒冷地区坝体采取聚胺脂喷涂施工措施后对坝体变形的影响，以及右坝肩渗漏对右坝肩岩体的影响，分析结果为托海水电站通过国家电力公司大坝安全监察中心大坝安全首次定检提供了科学依据。     

深基坑支护结构计算的有限元方法

针对软土地基的特性，本文提出了考虑土体抗力释放与结构模型随施工过程改变的新杆系有限元法，并 编制了求解支护结构内力与变形的计算程序，通过对事例分析．计算结果与实际情况非常吻合，证明了该方法的合理 性。     

Generation of Technology-Independent Retargetable Analog Blocks

This paper introduces a complete methodology for retargeting of analog cells to different sets of specifications. This methodology is technology-independent, thus allowing the migration, from one technology to another, of the circuit under retargeting. Careful integration of the device sizing and layout generation tasks via the incorporation of layout constraints during the sizing process allows to generate fully functional designs in a few minutes. The methodology is illustrated via the retargeting of a fully-differential Miller-compensated two-stage operational amplifier for a new set of specifications and two different technological processes.An erratum to this article can be found at     

薄板坯连铸工艺液芯压下的有限元分析

简要介绍世界几种主要薄板坯连铸工艺。着重叙述应用大型通用商业软件MSC.MARC。模拟液芯压下时铸坯的变形，确定最佳压下方案的有限元分析，液芯压下应该在结晶器出口处及二冷区扇形段开始部分进行，这样能减小铸坯的应变。     

石油测井仪器可靠性指标探讨

在分析常用可靠性指标及其应用现状的基础上，根据可靠性理论及石油测井仪器的特点。提出了石油测井仪器的可靠性模型。在探讨常用可靠性指标对石油测井仪器适用性的同时，提出将平衡稳定工作时间NWTURE和免维修测井井次NOLWNM作为石油测井仪器可靠性指标的思想；探讨了获取可靠性指标的途径。给出了推荐使用的石油测井仪器可靠性指标。     

全站仪在直升机悬停测试中的应用

介绍了如何将改造后的全站仪应用于直升机悬停性能测试的方法。经真实飞行试验检验，该方法理论严密，方案合理，改装简单，操作方便，成本低廉。较之原始的摄影测量法有无法替代的优点。     

气压传动与控制在电子专用设备上的应用

气压传动与控制已成为电子专用设备研制过程中一项不可缺少的内容 ,必须进行合理的气动系统设计及其控制 ,选择相应的气动元件以满足设备的功能要求。概述了气压传动与控制在电子专用设备上的应用。