连续驱动摩擦焊动态扭矩检测的新方法—VCMM法

连续驱动摩擦焊动态扭矩检测的新方法──ＶＣＭＭ法刘金合，罗键连续驱动摩擦焊扭矩是一个重要的工艺参数。摩擦焊扭矩是动态扭矩，具有时变性、速变性以及变化范围大等特点。现有的检测摩擦焊扭矩的方法均有一定的局限性’‘－’‘，本文提出了通过驱动主电机定子电压和...     

13SiMnNiCrMoV钢切口疲劳裂纹萌生门槛值

本文研究在13SiMnNiCrMoV 结构钢中用尖裂纹的应力强度因子来反映三点弯曲缺口试样的疲劳裂纹萌生规律。当 R=0.1,f=100Hz,试样尺寸 B×W×L=12.5×25×117mm 时,缺口名义应力幅的门槛值为Δσ_(th)=3315ρ~(0.352) MPa,0.5mm≤ρ≤5mmΔK_(th)=250ρ~(0.352) MPam~(1/2)门槛值与ρ有关。同时得到缺口裂纹萌生的循环次数 N_i 与名义应力幅Δσ、缺口曲率半径ρ的定量关系是N_i=3.98×10~(22)ρ~(1.62)/Δσ~(4.85),N_i≤10~(5.5)并讨论了(ΔK_1/ρ~(1/2))_(th)与ρ无关的结论。     

柔性纤维混凝土的疲劳特性研究

将柔性纤维掺入水泥混凝土可以大幅度提高混凝土的弯曲疲劳等路用性能,并通过试验建立了柔性纤维混凝土的疲劳方程.结果表明,柔性纤维不但能使混凝土的强度提高,更主要的是可以在重交通条件下,可成倍地提高混凝土的弯曲疲劳寿命.     

Microstructure and Mechanical Properties of Heat-treated GeSb_2Te_4 Thin Films

The effect of annealing on microstructure,adhesive and frictional properties of GeSb 2 Te 4 films were experimentally studied.The GeSb 2 Te 4 films were prepared by radio frequency(RF)magnetron sputtering,and annealed at 200℃and 340℃under vacuum circumstance,respectively.The adhesion and friction experiments were mainly conducted with a lateral force microscope(LFM)for the GeSb 2 Te 4 thin films before and after annealing.Their morphology and phase structure were analyzed by using atomic force microscopy(AFM)and X-ray Diffraction(XRD)techniques,and the nanoindention was employed to evaluate their hardness values.Moreover,an electric force microscope(EFM)was used to measure the surface potential. It is found that the deposited GeSb 2 Te 4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition;the adhesion has a weaker dependence on the surface roughness,but a certain correlation with the surface potential of GeSb 2 Te 4 thin films.And the friction behavior of GeSb 2 Te 4 thin films follows their adhesion behavior under a lower applied load.However,such a relation is replaced by the mechanical behavior when the load is relatively higher.Moreover,the GeSb 2 Te 4 thin film annealed at 340℃presents a lubricative property.     

聚醚合成工业齿轮油的研制

以聚醚为基础油辅以抗磨剂、抗氧剂、防锈剂等多种添加剂研制而成的KGW聚醚合成工业齿轮油具有优异的黏温性能和低温性能，优异的极压抗磨性，极优的减摩性能，可满足高负荷、强冲击等苛刻条件下各类齿轮传动装置的润滑要求。该系列产品达到国外同类油品质量水平。     

疲劳裂纹的灰色残差预测

借助灰色理论，建立了预测疲劳裂纹扩展的灰色残差预测模型，并应用此模型预测了某不锈钢构件腐蚀疲劳裂纹的扩展，得到了较高精度的预测结果，为疲劳裂纹预测提供了一种简易而可靠的新途径。     

宽带激光熔覆WCP/Ni基合金梯度复合涂层组织与摩擦磨损特性

研究了铸造WC_P/Ni基合金梯度复合涂层组织与摩擦磨损特性。结果表明,梯度复合涂层与基材实现了良好的冶金结合,涂层内有γ-Ni枝晶组织,γ-Ni＋M₂₃C 6共晶组织以及凝固结晶析出的M₆C、M₂₃C₆、M₇C₃等块状或条状组织;随着铸造WC_P体积分数的增加,复合涂层摩擦系数减小,耐磨性增加。19-4试样的耐磨性最高值为4.61,是基材的3倍以上。梯度涂层的磨损机理为磨粒磨损与粘着磨损的复合作用。     

在役钢筋混凝土结构基于可靠性的疲劳寿命分析

本文以结构的极限疲劳循环次数作为随机变量,基于可靠性理论提出了在役结构疲劳剩余寿命的预测方法,分析了多种工况下结构在未来服役期内的疲劳可靠性和疲劳剩余寿命。算例表明,通过对在役结构疲劳寿命及可靠性的分析,不仅可以预测在目标可靠度下的疲劳寿命,而且可以根据需要确定合适的交变荷载的频率、服役时间以及相应的疲劳可靠指标,从而为结构的合理利用起指导性作用。     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

Time and Temperature Factors in Construction of Rock Strength Criteria

Using the synthesis of the kinetic concept on solid strength and the Coulomb - Mohr strength theory as the base, the failure conditions taking into account the time and temperature factors are obtained.