Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

聚合物冷拉过程的流函数分析

用流函数法分析了聚合物拉伸成形时，颈缩的发生和扩展过程，文中论证了采用流函数法的优越性和适用性，并将流函数法计算结果和有限元法计算结果作了对比。     

以技术进步促进蒸汽能源的节约

本文运用“软科学”一即通过建立数学模型，进行系统分析和系统优化，阐述对蒸汽管网优化运行的方法及原理，达到提高供热效率及节能降耗的目的．     

Important features of Iris OSQL

OSQL is the object-oriented database language developed for the Iris object-oriented database management system at Hewlett-Packard Laboratories. Its three fundamental constructs are objects, types, and functions. This paper provides an overview of the underlying concepts and some important features of OSQL.     

On the mechanical behavior of aluminum alloys reinforced by long or short alumina fibers or SiC whiskers

This study was initiated to examine the dispersion of longitudinal and transverse waves in metal matrix composites in order to obtain the dynamic elastic modulus and to evaluate various models for predicting the composite's macroscopic elastic constants from the properties of its constituents. The materials chosen for this investigation were alumina continuous fibers on the one hand and alumina and SiC short fibers on the other hand, all embedded in an aluminum alloy matrix. In addition, some indications have been obtained experimentally for the acoustoelastic effect in the composite.     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Non-parametric empirical Bayes procedure

In this paper we introduce an empirical Bayes procedure for estimating an unknown parameter, say θ. This procedure gives the empirical Bayes estimator for θ and its associated minimum posterior risk in closed forms without estimating the unknown prior density function of θ. In such procedure the posterior probability density function of θ is not required. A sufficient statistic for θ with conditional probability density function in the one parameter exponential family is required. Instead of estimating the unknown prior density function, the marginal density function of the sufficient statistic must be estimated. As special cases the empirical Bayes estimators and their respective minimum posterior risks of the failure rate for the exponential distribution, the unknown scale parameters of Weibull and gamma distributions are obtained in simple forms as special cases. Numerical results and a simulation study are introduced to (i) investigate how the number of available past experiments and the sample size of each influence the accuracy of the empirical Bayes estimator, (ii) make a comparison between the presented procedure and the Bayes procedure when the prior probability density function of the parameter θ is gamma.     

New nanocomposite materials based on polymerization of [oligo(oxyethylene) methacrylates] in the presence of montmorillonite clay

Intercalation of poly[oligo(oxyethylene) methacrylates] onto sodium montmorillonite (MMT) clay has been investigated. A polymer–clay hybrid has been synthesized through intercalation of the monomer followed by its solution free‐radical polymerization. Eight polymer–clay hybrids were prepared using different weight ratios of clay, different oligo(oxyethylene) lengths and different proportions of crosslinker. Evidence of the development of nanostructures is obtained from scanning electron microscopy, and wide‐angle X‐ray diffraction studies support these results which show disappearance of the peak characteristic to d₀₀₁ spacing. In this hybrid MMT is dispersed homogeneously in the polymer matrix. © 2003 Society of Chemical Industry     

采用多模复合导引头提高反舰导弹突防能力

分析了现有反舰导弹制导体制的特点，提出了反舰导弹如采用被动微波／红外成像双模复合导引头，将是提高其突防能力的有力举措，同时提出了研制主被动／红外成像三模复合导引头的建议，并给出了三模导引头结构布局示意图。