转向驱动轮轮胎测力仪研究

该测力仪在结构上采用双等速万向节装置，不仅能用于转向轮和非转向轮的测量，并且解决了转向驱动轮的动力测量问题，对于四轮驱动的军用轮式车辆实车测试有着十分重要的意义。测力仪将轮胎动载荷、扭矩、侧向力、回正力矩、驱动力和外倾力矩的测量转化为测力筋拉压力的测量，大大提高了测量精度和抗干扰能力。     

磨机大齿轮对缝处产生张口的初探

针对大中型磨机大齿轮对缝处在使用中会产生张口现象而降低其使用寿命的问题,从分析产生张口的原因入手,通过理论计算,提出设计的配合间隙,并指出在安装与使用中应注意的问题.     

机械研磨 Ni_(50)B_(50)合金形成非晶的过程

本文研究了机械研磨 Ni_(50)B_(50)合金非晶的形成过程。唯象地提出用 J-M-A 方程描述此过程,并作了简单的讨论。     

非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经预退火后的晶化动力学的DTA研究

研究了非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经400℃，保温10min预退火后的晶化动力学。结果表明；该合金的晶化相为α-Fe固溶体和Sm2Fe17Cx金属间化合物，两相的晶化表观激活能分别为557KJ/mol和514KJ/mol，当晶化体积分数为60%时，α-Fe相的晶化激活能达极大值；Sm2Fe17Cx相晶化激活能则随其晶化体积分数的增加而逐渐减小。     

Development of an integrated model for airflow in building spaces

In building energy simulation, an integrated modelling of airflow in the building needed. Therefore, in this paper two approaches are used for building energy simulation: zonal network for modelling of the building segments and Computational Fluid Dynamics (CFD) for modelling of the airflow. It is noted that a synchronize solution process is needed for the building and the CFD equation-sets. For this purpose an iterative procedure is used to corresponding solution of these equations.     

Improvement of oxygen mass transfer estimation from oxygen concentration measurements in bubble column reactors

An original procedure has been established for estimating the overall volumetric mass transfer coefficient using the oxygen concentration curves resulting from the usual gassing-in and gassing-out method. This procedure was applied to experimental data obtained in a small scale bubble column using both tap water and a coalescence-inhibiting liquid mixture that represents the coalescence behavior of biological media. It is based on the analysis of the characteristics times of the system, including those of the hydrodynamics of the two phases, the sensor dynamics and the system inertia when the gas composition is modified. A numerical procedure was developed to estimate the characteristic time of the system inertia t_i, using the assumption that this inertia is nearly independent of superficial gas velocity U_G. The calculations confirmed that the optimized t_i value was nearly independent of U_G and of the coalescence behavior of the liquid phase. Additionally, the resulting K_La_L values for tap water were closer to the correlation of Shah et al. [1982. Design parameters estimations for bubble column reactors. A.I.Ch.E. Journal 28, 353-379] than those of other conventional models. Finally, the original procedure was also reported to reduce significantly the square sum deviation between the predicted and the measured oxygen response curves.     

Analytical solution for the axisymmetric plane strain electroelastic dynamics of a special non-homogeneous piezoelectric hollow cylinder

By virtue of the introduction of a dependent variable and the separation of variables technique, the axisymmetric plane strain electroelastic dynamic problem of a special non-homogeneous piezoelectric hollow cylinder is transformed to a Volterra integral equation of the second kind about a function with respect to time, which can be solved successfully by means of the interpolation method. Then the solutions of displacements, stresses, electric displacements and electric potential are obtained. The present method is suitable for a piezoelectric hollow cylinder with an arbitrary thickness subjected to arbitrary mechanical and electrical loads. Numerical results are finally presented.     

Molecular Dynamics Simulation of Gas Diffusion in B2O3 and SiC

Molecular dynamics simulation using a universal force field has been employed to determine the diffusion coefficients of O2 and Na2SO4 vapor into B2O3 and SiC from 700 K to 1273 K, respectively. Einstein diffusion was observed in a 250～300 ps simulation.     

Simulation of Economic Dynamics under Ecological Balance Conditions

A model of economic dynamics under stable ecological balance conditions is proposed. A methodology of construction of an optimal growth path is constructed for this model.     

The three-dimensional architecture of the mitotic spindle,analyzed by confocal fluorescence and electron microscopy

Fluorescence microscopy techniques have become important tools in mitosis research. The well-known disadvantages of fluorescence microscopy, rapid bleaching, phototoxicity and out-of-focus contributions blurring the in-focus image are obstacles which still need to be overcome. Confocal fluorescence microscopy has the potential to improve our capabilities of analyzing cells, because of its excellent depth-discrimination and image processing power. We have been using a confocal fluorescence microscope for the study of the mechanism of poleward chromosome movement, and report here (1) a cell preparation technique, which allows labeling of fixation sensitive spindle antigens with acceptable microtubule preservation; (2) the use of image processing methods to represent the spatial distribution of various labeled elements in pseudocolour; (3) a novel immunoelectron microscopic labeling method for microtubules, which allows the visualization of their distribution in semithin sections at low magnification; and (4) a first attempt to study microtubule dynamics with a confocal fluorescence microscope in living cells, microinjected with rhodamine labeled tubulin. Our experience indicates that confocal fluorescence microscopy provides real advantages for the study of spatial colocalization of antigens in the mitotic spindle. It does not, however, overcome the basic limits of resolution of the light microscope. Therefore, it has been necessary to use an electron microscopic method. Our preliminary results with living cells show that it is possible to visualize the entire microtubule network in stereo, but that the sensitivity of the instrument is still too low to perform dynamic time studies. It will be worthwhile to further develop this new type of optical instrumentation and explore its usefulness on both fixed and living cells.