65Mn钢CCT曲线及圆锯片淬火工艺

用全自动相变测定仪测定了圆锯片常用６５Ｍｎ钢的连续冷却转为曲线，研究了不同连续冷却速度下得到的组织，为合理制订圆锯片的淬火工艺提供了依据，得到了最佳淬火工艺曲线。     

小型预制桩基础承载特性数值模拟研究

本文建立硬化土本构模型,针对江苏省软土地区的土质条件选取数值计算参数,通过PLAXIS 2D软件对小型预制桩在的单桩水平受荷及竖向受荷进行数值模拟,得到桩身弯矩沿桩长的分布以及荷载-位移曲线,分析小型预制桩基础桩身弯矩的分布特点,并探求其在水平及竖向荷载作用下的承载特性,进而能够为小型预制桩基础工程设计以及计算方面提供一定的参考依据。     

On certain aspects of strain rate sensitivity of sheet metals

The formability of a material depends upon the strain hardening and strain rate hardening of the material. In this study, constitutive parameters using the power law constitutive equation are determined for six different strength steels and two aluminum alloys over different strain ranges, including approximations of the postuniform elongation range. Constitutive parameters are found to be different at different strain ranges. The strain hardening of steels increases with strain at low strain levels (less than 5%) and decreases at high strain levels (greater than 10%). Strain rate hardening decreases with strain for all steels and aluminum alloys. Uniform elongation depends only on strain hardening, and postuniform elongation depends only on strain rate hardening. However, the total elongation depends on both strain hardening and strain rate hardening.     

Study on Surface Engineering of Normalized Steels Subjected To Machine

Engineering the surfaces of components to improve the life and performance of parts used in automotive and aerospace engineering is the active area of research. Suitable Thermal/Mechanical/Thermo mechanical surface engineering treatments will produce extensive rearrangement of atoms in metals and alloys and corresponding marked variations in Physical, Chemical and Mechanical properties. Among the more important of these treatments are heat treatment processes such as hardening by Quenching, Induction hardening and Case Carburizing which rely on phase transformations to produce desired changes in mechanical properties. Other processes where phase transformation occur are casting, welding and machining etc. [1] Phase transformation may be homogeneous or heterogeneous. Homogeneous involves rearrangements in the structure of the material taking place simultaneously in all parts of the solid, while the heterogeneous transformation involves structural changes which are more localized. Alternatively they could be called as Isothermal and Nonisothermal transformation. But irrespective of the classification, these transformations alter the structure of the material giving rise to changes in the mechanical and physical properties of the processed material. It is of interest to review some consequences of surface modification in isothermal (Normalizing) and nonisothermal transformations (Machining) of low carbon steels.     

接触疲劳过程中的诱发相变和冷作硬化SCIEI

研究了三种丝杠钢的接触疲劳性能。利用TEM和背散射Mossbauer谱研究了三种钢在接触疲劳前后的显微组织结构;测量了接触区中心线下显微硬度随层深的变化。结果表明:接触应力诱发A_R→M相变,并导致一定深度的冷作硬化。讨论了诱发相变和冷作硬化对接触疲劳性能的影响。     

长轴表面激光淬火变形与控制

应用激光淬火强化技术控制长轴的淬火变形，分析了激光淬火变形的原因和影响因素。研究结果表明，激光淬火不仅可使长轴振摆变形量控制在很小的范围内，而且可将已变形的长轴校直到很高的精度。     

扫描速度对硼铸铁气缸套表面钨极氩弧硬化效果的影响

研究了钨极氩弧扫描速度对硼铸铁表面硬化效果的影响规律。结果表明：扫描速度增加,硬化层宽度、深度减小,而硬度提高,裂纹率增大；硬化层硬度沿层深的分布是从表及里由高而低,在过渡区下降缓慢；沿层宽的分布是层中心最高,向两侧逐渐降低,直至硼铸铁基体达到最低值；在保证不出现裂纹的条件下,硬化层表面的最高硬度值可达61．4HRC,硬化层最高显微硬度值可达1156．4HV0．1；硼铸铁材料采用氩弧热源淬火时,淬硬层与基体之间过渡区明显,硬化区组织为莱氏体,过渡区为马氏体、残余奥氏体和少量石墨。     

高锰钢爆炸硬化

对高锰钢爆炸硬化工艺和硬化机理进行了综述,并对爆炸硬化的研究进展及需要开展的进一步工作作了简单介绍。     

淬火温度对铸造Fe—B—Ti合金组织和性能的影响

通过不同的热处理淬火温度改变铸造Fe—B—Ti合金的组织，探讨了铸造Fe—B—Ti合金不同组织与性能的关系。试验结果表明：淬火温度较低时，硼化物变化较小，网状分布趋势明显；淬火温度较高时，硼化物断网和团聚化趋势明显加快。淬火温度1050℃时，硼化物网状特征消失，基本上都变成了团块状、颗粒状和杆棒状分布。随着淬火温度升高，硬度和韧性增加，超过1000℃，硬度和韧性变化不明显。淬火温度1050℃时，综合性能良好。     

应变速率对中碳低温贝氏体钢强塑性的影响

摘要：为探索低温贝氏体钢的断裂行为,研究应变速率对低温贝氏体钢TRIP效应的影响,采用不同应变速率的拉伸试验对低温贝氏体钢的强塑性进行研究。利用扫描电镜（SEM）、透射电镜（TEM）及X射线衍射（XRD）等试验方法对低温贝氏体钢的微观组织、断口形貌及裂纹走向进行表征。结果表明,随着应变速率的提高,试验钢的屈服强度由771MPa上升至806MPa,抗拉强度由1554MPa上升至1606MPa,断后伸长率由13.5%下降至9.0%。主要原因是高应变速率拉伸引发的绝热温升抑制了残余奥氏体的马氏体相变,对试验钢塑性造成负面影响。