高沸点溶剂法合成原乙酸三甲酯

对低沸点溶剂法制备原乙酸三甲酯工艺进行了改进，比较了煤油、2-乙基己醇、氯苯、异佛尔酮、邻苯二甲酸二丁酯、乙二醇二丁醚等高沸点溶剂对反应的影响，筛选出最优高沸点溶剂煤油：研究了新反应体系的醇解pH值、溶剂的循环使用次数对反应的影响及溶剂循环损耗率，结果表明，醇解的最佳pH值为5．6；随着溶剂循环次数增加，原乙酸三甲酯收率从83．6％(1次)逐渐下降到76．7％(16次)；溶剂次平均损耗率4．6％。实现了直接蒸馏产品，溶剂循环使用的新工艺。避免了旧工艺先蒸溶剂，后蒸产品，产品大量分解，收率低等缺点。     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

Abrasion erosion of concrete by water-borne sand

Hydraulic concrete structures frequently experience long-term abrasive erosion by water-borne sand, resulting in surface damage and eventually limiting their service life. In this study, the investigation of abrasion erosion tests on concrete with various water to cementitious material ratios (w/cm) was performed. The effects of the constituent materials on concrete structure abrasion erosion resistance were studied. The test results show that: (1) reduction in the w/cm ratio increases the tested concrete abrasion resistance; (2) the splitting tensile strength is a viable indicator for concrete abrasion resistance; (3) high permeability concrete exhibits weak abrasion resistance; and (4) concrete and low strength concrete made with coarser aggregate exhibit greater abrasion resistance.     

Thermodynamic Criteria for the Maximum and Minimum Strength of Fibre-Reinforced Composite Materials

The overall performance and reliability of composite materials are, in most cases, dependent upon the behaviour of the reinforcement-matrix interface, particularly upon its ability to transfer stress.

A theory for predicting thermodynamic conditions for the maximum and zero-adhesion at the reinforcement-matrix interface is tested in this paper, based on experimental data. Proposed is a model of the relationship between mechanical properties of composite materials (tensile strength, flexural strength, Young's modulus and impact resistance) and energetic properties of matrix and reinforcement expressed by the energy ratio a = γ_l/γ₂.     

悬浮法合成聚丙烯腈高吸水性树脂

以偶氮二异丁腈为引发剂，用悬浮聚合法合成了交联聚丙烯腈，然后对其进行水解，得到了高吸水性聚丙烯腈。交联剂用量和水解条件对树脂吸水倍数的影响很大。树脂吸去离子水倍数为420倍，平均粒径为250μm。     

高效液相色谱法测定卷柏中的穗花杉双黄酮

用反相高效液相色谱法测定卷柏提取物中的穗花杉双黄酮。结果表明：穗花杉双黄酮在质量浓度为41.2mg／L～206mg／L时，峰面积Y与其质量浓度X的线性关系良好，回归方程为Y=547．028X 15．4895(r=0.9999)，最低检测限为2．0μg/L；穗花杉双黄酮的平均回收率为99．42％(n=3)，相对标准偏差RSD为0．79％；连续进样、日内进样和日间进样所得检测结果的RSD分别为0．12％、0．11％和0．11％。     

Effect of the use of mineral filler on the properties of concrete

Engineers of the concrete technology are increasingly concerned with the material passing through a sieve of the size under 0.149 mm. Materials called very fine aggregate or mineral filler may affect the performance of concrete in an either positive or a negative way. Discussions on aggregate containing very fine material are vitally important. Washing the aggregate residue has been the sole way to solve this matter to date. This is mainly based on the debatable opinion that materials of this kind are regarded as clay material. The goal of the study was to determine how the content of mineral filler might affect properties of concrete. Two types of aggregates with different amounts of cement and mineral filler were used. Basically, mineral filler replaced sand. The effect of applying different amounts of mineral filler on concrete was then determined. The addition of 7-10% of mineral filler to fine aggregate (0-2 mm) was found to considerably improve the properties of concrete.     

PVC发泡制品用助剂--优泡剂

分析了PVC发泡制品成型加工时存在的缺陷,说明了添加优泡剂可弥补PVC发泡制品的缺陷,提高泡孔质量,介绍了优泡剂的品种和使用场合及使用量。     

反相高效液相色谱法测定meso-四苯基卟啉钴的纯度

采用反相高效液相色谱法测定合成meso-四苯基卟啉钴的纯度;以甲醇乙腈二氯甲烷(体积比为55∶35∶10)为流动相,ShimpackCLCODS柱(150mm×6.0mmi.d,5μm)为分离柱,流速为1.5mL/min,检测波长420nm;meso四苯基卟啉钴的测定在1.0～10μg/mL时线性关系良好(相关系数r=0.9993),加标回收率为97.03%～101.42%,重复进样的相对标准偏差RSD为0.64%～2.92%(n=5)。方法的准确度高,精密度好,实际应用效果好。