消防水箱设计中常见错误及改正措施

根据现行消防技术规范的有关规定，结合建筑工程消防监督审核的工作实践，指出了消防水箱设计中常出现的错误并提出了相应的改正措施。     

湛江电厂1号发电机定子冷却水处理方式的改造

简述发电机铜导线腐蚀机理,湛江电厂1号发电机定子冷却处理方式改造前后各自的特点。比较新旧两种方式水质处理效果、安全性、经济性。采用超净化装置后,解决了原来处理方式的所有缺点,水质达到质量标准, 创造良好的经济效益,值得推广改造和借鉴。     

基于模糊神经网络的感应加热电源温度控制

通过对原有感应加热电源温度控制方法的分析，提出了一种适合于非线性系统基于模糊神经网络的温度控制方法，并介绍了该系统的组成及实现方法。     

Analysis on the Logarithmic Model of Relationships

The logarithmic model is often used to describe the relationships between factors.It often gives good statistical characteristics.Yet,in the process of modeling of soil and water conservation,we find out that this“good”model cannot guarantee good result.In this paper we make an inquiry into the intrinsic reasons.It is shown that the logarithmic model has the property of enlarging or reducing model errors,and the disadvantages of the logarithmic model are analyzed.     

Effect of Hot Band Annealing on Magnetic Properties in 3% Si Grain‐oriented Electrical Steels

Hot band annealing is known to be a prerequisite for good magnetic properties irrespective of manufacturing methods in grain‐oriented Fe‐3 wt.% Si electrical steels. In this study, the effects of hot band annealing on magnetic properties were investigated in 3% grain‐oriented electrical steels of low soluble AI contents and one‐stage cold rolling. Microstructure and precipitate distribution were compared with hot band annealing conditions. Secondary recrystallization behaviour with hot band annealing condition was also discussed.     

聚氨酯基pH/温度敏感性水凝胶的结构形态

通过阴离子型端丙烯酸酯基聚氨酯(UAA)与N-异丙基丙烯酰胺(NIPAAm)的共聚交联反应,制备了pH/温度敏感性水凝胶,分析了水凝胶的结构形态及溶胀水的状态.结果表明,凝胶相结构均匀,随聚氨酯含量的降低,凝胶的骨架变得松散,并且孔道结构增大,导致溶胀凝胶中不可冻结水含量及凝胶强度的降低.     

电气设备发热故障的预防和处理

介绍了电气设备发热故障的危害和形成原因,并就各种原因引起的发热故障的预防与处理方法进行了阐述。     

钢管热连轧机架爆炸复合衬板的研究

在分析了各种钢板复合工艺优缺点的基础上,首次提出钢管热连轧机架耐磨衬板采用爆炸焊接工艺进行复合.衬板背面选用韧性强和焊接性能好的低碳低合金结构钢,衬板工作面选用中高碳多元低合金耐磨合金钢.在此基础上,研究了两种不同钢板的爆炸复合工艺,检测了复合面的组织和性能,并研究了复合钢板的热处理工艺,着重解决了复合钢板高温热处理时的氧化和淬火冷却时的变形.新开发的复合钢板在钢管热连轧机架上具有优良的使用效果.     

我国水资源可持续发展战略之研究

分析了中国水资源的特点和基本概况,探讨了水资源利用而应采取的全方位措施.即增强忧患意识,改变思想观念,保护自然资源,优化生态环境.     

Aspects of microstructure in low carbon steels produced by the CSP process

The solidification structure, microstructure evolution during rolling and precipitates with nanometers in dimension of the low carbon steels produced by CSP process with thin slabs have been studied in recent years. Important differences in microstructure and mechanical properties between the CSP products and the conventional one were observed. These differences may arise from the much rapider solidification rate and cooling rate after casting of the thin slabs. Some aspects of the microstructure for the low carbon steels of the CSP thin slabs are summarized and compared with the conventional one.