混凝土骨料二维分布的模拟和应用

通过在一个矩形截面上模拟混凝土骨料的实际分布，获得了该截面上任一点的骨料分布密度和骨料分布的统计特性。模拟结果表明，当模拟次数趋向于无穷大时，截面上任一点的骨料分布密度趋向于定值，对于不同的骨料面积百分数，骨料分布密度曲线的形状十分相似，均由上升段和水平段两部分组成。基于这些模拟结果，利用数学拟合获得了骨料分布密度的解析表达式，并被混凝土实验所初步证实。作为一个应用，本文计算了混凝土截面上各点的氯离子扩散系数。     

液氨储罐保冷改造效果评定

作者结合实例，论述了氨罐保冷改造的设计、选材及施工，给出了改造后两年的测试结果，并对测试结果进行了分析。     

Equivalent Conditions for Convergence of Splittings of Non-Hermitian Indefinite Matrices

We present some sufficient and necessary conditions for convergent splitting of a non-Hermitian indefinite matrix. Some sufficient conditions to determinate a matrix with a (strongly) dominant symmetric part for a class of boundary value problem are also obtained. These results are applicable to identify the convergence of iterative methods for solving large sparse systems of linear equations.     

主动约束层阻尼板结构动力学建模研究

将有限元法和GHM法相结合，给出了建立主动约束层阻尼（ACLD）板结构动力学模型的新方法。建模时，考虑到粘弹材料（VEM）的纵向位移影响，采用GHM方法描述VEM的本构关系，解决了VEM的力学特性随温度和频率变化的难点，避免因VEM的复杂本构关系而产生的微分积分方程。算例表明本文给出的建模方法是准确的，ACLD结构能够有效控制结构振动。     

钢锭零能少氧化均热轧制的研究

根据计算机的辅助分析,采用新的钢锭传搁、注后强制水冷却、垫铁脱模等工艺后,入炉钢锭的热焓已超过开坯轧制需要,利用普通均热炉代替钢锭保温车,可完全依靠到钢锭自身潜热与显热进行均热。对不同锭型与钢种采用经试验的最佳时间均热后再轧制,收与保温车均热钢锭直接轧制相同的效果。     

Porosity of recycled concrete with substitution of recycled concrete aggregate: An experimental study

In this paper, we present the experimental analysis of samples of recycled concrete (RC) with replacement of natural aggregate (NA) by recycled aggregate originating from concrete (RCA). The results of the tests of mechanical properties of RC were used for comparison with tests of mercury intrusion porosimetry (MIP), in which the distribution of the theoretical pore radius, critical pore ratio, the surface area of the concrete, threshold ratio and average pore radius were studied at ages of 7, 28 and 90 days. The results showed some variation in the properties of the RC with respect to ordinary concrete. Porosity increases considerably when NA is replaced by RCA. Additionally, a reduction in the mechanical properties of the RC is seen compared with ordinary concrete when porosity increases.     

高水固结尾砂充填采矿充填体合理配比的研究

高水固结尾砂充填采矿是一种新型充填采矿法。试验测定了高水固结尾矿充填体的强度和变形特征；研究分析了影响充填体强度的主要因素、高水充填工艺的特殊要求，以及上向，下向进路开采对充填体强度和稳定性的要求，提出了满足支护强度，工艺及经济需求的充填材料的合理配比范围。     

喷锚结合水泥搅拌桩在基坑支护中的应用

结合紫金苑工程实例,分析喷锚结合水泥搅拌桩在基坑支护中的应用并总结施工、监测经验。     

Production of biodiesel from waste fryer grease using mixed methanol/ethanol system

Transesterification of waste fryer grease (WFG) containing 5–6 wt.% free fatty acid (FFA) was carried out with methanol, ethanol, and mixtures of methanol/ethanol maintaining the oil to alcohol molar ratio of 1:6, and initially with KOH as a catalyst. Mixtures of methanol and ethanol were used for transesterification in order to use the better solvent property of ethanol and rapid equilibrium using methanol. Formation of soap by reaction of FFA present in WFG with KOH instigated difficulty in the separation of glycerol from biodiesel ester. To untangle this problem, two-stage (acid and alkali catalyzed) method was used for biodiesel synthesis. More than 90% ester was obtained when two-stage method was used compared to ∼ 50% ester in single stage alkaline catalyst. In the case of mixed alcohol, a relatively smaller amount of ethyl esters was formed along with methyl esters. Acid value, viscosity, and cetane number of all the esters prepared from WFG were within the range of the ASTM standard. Esters obtained from WFG showed good performance as a lubricity additive.     

Degradation of polyethylene terephthalate films in the presence of lubricants for HFC 134a: a critical issue for hermetic motor insulation systems

Earlier studies conducted in the use of sealed tubes with polyalkylene glycol lubricants and polyethylene terephthalete (PET) films revealed that the PET films exhibited embrittlement and (visual) degradation. This led to an investigation of PET embrittlement mechanisms with the new lubricants used with HFC 134a. The lubricants studied were three polypropylene glycols (the monol, the diol and the completely end-capped glycols), pentaerythritol ester and a blend of monol and ester. The effects of moisture content, temperature and lubricant structure were studied. All lubricants in this study were of viscosity grade ISO-32 (150 SUS). The results were compared to PET film embrittlement in the presence of CFC 12 and mineral oil. This study reconfirmed the earlier findings that the PET films must be dried to lower than 0.1 wt.% moisture content for use in hermetic systems. This paper discusses the effect of the moisture content of the lubricant and the effect of the lubricant structure on PET films. The dependence of the various mechanisms on temperature is shown. Esters and end-capped polyalkylene glycols are recommended for use with HFC 134a.